« previous next »
Pages: 1   Go Down

Author Topic: 3D printing  (Read 9719 times)

0 Members and 1 Guest are viewing this topic.

NYKenn

  • Active Members
  • ***
  • Posts: 523
  • Distinguished Pistol Shot
    • View Profile
    • The Firing Line
3D printing
« on: May 31, 2025, 08:04:18 pm »
Picked up a 3D printer. Mainly because New York is starting background checks and may begin registering users. Typical Socialist crap from our useless Democratic/Socialist state government.

Have found many files online  for Dillon accessories to make, but zero for Star so far.
Anyone have any or know of some?
Would like a powder measure top to sort powder/bullet when puling.
Possibly other items as well.
Anyone have any or know of a source.
Thanks in advance.

Logged
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms shall not be infringed"

WWW.TheFiringLineNY.com

NYKenn

  • Active Members
  • ***
  • Posts: 523
  • Distinguished Pistol Shot
    • View Profile
    • The Firing Line
Re: 3D printing
« Reply #1 on: May 31, 2025, 08:06:00 pm »
Maybe a primer follower as well.

Logged
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms shall not be infringed"

WWW.TheFiringLineNY.com

NYKenn

  • Active Members
  • ***
  • Posts: 523
  • Distinguished Pistol Shot
    • View Profile
    • The Firing Line
Re: 3D printing
« Reply #2 on: June 18, 2025, 07:58:10 pm »
No one?
Logged
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms shall not be infringed"

WWW.TheFiringLineNY.com

Cousin Daniel

  • Active Members
  • ***
  • Posts: 43
    • View Profile
Re: 3D printing
« Reply #3 on: June 19, 2025, 12:30:49 am »
I don't have a file to share but a case feeder would be completely doable 3d printing.

I machined one once and understand why they cost $250

A cheap stand in would encourage me to buy a few for presses that lack them.
Logged

FOR_Star

  • Active Members
  • ***
  • Posts: 94
  • Star Universal owner since 1979
    • View Profile
Re: 3D printing
« Reply #4 on: July 08, 2025, 10:39:43 am »
NYKenn,

How about an off-ramp/finished cartridge slide at the taper crimp station that replaces the Safety Cam (#39U), or attaches to the Safety Cam Standard (#40)?

Folks make these out of sheet metal in a form of origami exercise.  :)

Warren
Logged
Warren
Fair Oaks Ranch, Texas
Star owner since 1979

brian_a_mcmillen

  • Active Members
  • ***
  • Posts: 22
    • View Profile
Re: 3D printing
« Reply #5 on: July 21, 2025, 08:43:21 pm »
I only printed one item for my Star.  I started loading 22TCM and needed the case feeder top plate that would work with the .223 plunger.  The 9mm plate was too short and there was no way the .223 plate would work so I went to tinkerCAD and designed one.  It works!!
Logged
BMcMillen

NYKenn

  • Active Members
  • ***
  • Posts: 523
  • Distinguished Pistol Shot
    • View Profile
    • The Firing Line
Re: 3D printing
« Reply #6 on: July 23, 2025, 06:46:38 pm »
Will take a look into TinkerCad, but not yet advanced enough (or have enough time) to design yet.
Maybe later!

Logged
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms shall not be infringed"

WWW.TheFiringLineNY.com
Pages: 1   Go Up
« previous next »