« previous next »
Pages: 1   Go Down

Author Topic: Star for a .30 Cal Carbine?  (Read 16777 times)

0 Members and 1 Guest are viewing this topic.

jonhester

  • Active Members
  • ***
  • Posts: 8
    • View Profile
Star for a .30 Cal Carbine?
« on: March 07, 2013, 04:44:54 pm »
BRAND new to the board.
Would a Star have ever been configured for a .30 Carbine load?
Are there any Star users in the Atlanta area that would be willing to look over a press and help a newbie figure this thing out?
TY in advance!
 :)
Logged
Shoot till it stops movin...once is enough if ya aim right,

rbwillnj

  • Global Moderator
  • ****
  • Posts: 1226
    • View Profile
    • Star Machine Works
Re: Star for a .30 Cal Carbine?
« Reply #1 on: March 07, 2013, 06:24:32 pm »
A Star Universal could be configured for 30 Carbine, Star offered shell plates and dies for 30 Carbine.  Early Stars used steel sizing dies.  Later they used Lifetyme carbide sizing dies.   In most cases the steel sizing dies have been replaced with carbide dies, but you might come accross one that still has a steel sizing die.

Sorry, not in the Atlanta area, but if you post pictures I'm sure folks will chime in with their thoughts. 
Logged
Star Machine Works
Star, the original blue Press.  Made by machinist, not machines.
www.StarMachineWorks.com

jonhester

  • Active Members
  • ***
  • Posts: 8
    • View Profile
Re: Star for a .30 Cal Carbine?
« Reply #2 on: March 08, 2013, 10:45:42 am »
thanks!
Here's a pic of the machine. Safe to say you can use either steel or carbide dies in a Universal?
I'm also still trying to determine if this is a Universal or a Progressive machine? Can you determine that without removing the shell plate?
Logged
Shoot till it stops movin...once is enough if ya aim right,

rbwillnj

  • Global Moderator
  • ****
  • Posts: 1226
    • View Profile
    • Star Machine Works
Re: Star for a .30 Cal Carbine?
« Reply #3 on: March 08, 2013, 11:21:17 am »
It is a Star "Universal" model produced in 1965 or later.   It has a Lifetyme carbide sizing die.   I can't see if it has a taper crimp die installed, or if the taper crimp station has a 3/8" hole, or is drilled and taped for a 11/16-24

From what I can see in the picture, it looks like a decent machine.

Note: For 30 Carbine, even though it has a carbide die installed, it's best to use some case lube.
Logged
Star Machine Works
Star, the original blue Press.  Made by machinist, not machines.
www.StarMachineWorks.com

jonhester

  • Active Members
  • ***
  • Posts: 8
    • View Profile
Re: Star for a .30 Cal Carbine?
« Reply #4 on: March 08, 2013, 12:07:16 pm »
Would you gander a guess on a value?
Logged
Shoot till it stops movin...once is enough if ya aim right,

fc60

  • Active Members
  • ***
  • Posts: 493
    • View Profile
Re: Star for a .30 Cal Carbine?
« Reply #5 on: March 08, 2013, 08:22:16 pm »
Greetings,

I have machined 30 Carbine die sets in the past. In fact, I have a request in now for a new set.

I am a bit puzzled, is the Star pictured equipped with 30 Carbine dies? Or, are you wondering about converting to 30 Carbine?

As to value, do a search on eBay for completed auctions. I have not seen a 30 Carbine sold lately; but, it might bring a good price as it is not too common. Best scenario is to get two beered up bidders after the same tool.

Cheers,

Dave
Logged

jonhester

  • Active Members
  • ***
  • Posts: 8
    • View Profile
Re: Star for a .30 Cal Carbine?
« Reply #6 on: March 08, 2013, 09:42:25 pm »
The Star currently has .38 Special dies in it. Am I getting into a major piece of work by converting this machine to 30 carbine?
Logged
Shoot till it stops movin...once is enough if ya aim right,

jonhester

  • Active Members
  • ***
  • Posts: 8
    • View Profile
Re: Star for a .30 Cal Carbine?
« Reply #7 on: March 11, 2013, 11:31:16 am »
Adding pics...
Logged
Shoot till it stops movin...once is enough if ya aim right,

Hugh Tyer

  • Active Members
  • ***
  • Posts: 49
    • View Profile
Re: Star for a .30 Cal Carbine?
« Reply #8 on: March 11, 2013, 04:12:45 pm »
Jon I have sent a PM
Hugh
Logged
Pages: 1   Go Up
« previous next »