Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - cc656d

Pages: « 1 2 3 4 5 6 7 8 9 »
91
Stars Want to Sell/Want to Buy / Re: Wtb 49u angle
« on: January 22, 2012, 07:06:19 pm »
That part on EBAY is # 48 primer slide angle lever not the # 49u angle lever cam. They work together but they are not the same!

92
Stars Want to Sell/Want to Buy / Re: Phelps Star ????
« on: January 04, 2012, 09:12:24 pm »
The powder cam and the powder cam base do not look like any of the nine ( 9 ) Stars that I have, so I think thar the complete tool is a Phelps.

93
Stars Want to Sell/Want to Buy / Re: Phelps Star ????
« on: January 04, 2012, 04:53:31 pm »
The tool head on the tool is Phelps and the tool has non Star features which I think is a Phelps.

Thank you
Ricky

94
Star Reloaders / Re: CCI Large Pistol Primers getting sideways
« on: December 31, 2011, 11:24:12 am »
Problems can occur with primers . I purchased my first Star in [no e-mail]@. I used Remington primers for years but changed in the mid 80's . I loaded a lot ( bullseye shooting ) and Remington gotto the point of failure to feed in my Star. This would happen about once per hundred. It became a pain to clean the tool of loose powder. Remingtons Quality Controll was lacking. Upon examining the primers that gave problems I found that they were oval , not round and this was enough for the primers hagg up in the primer magazine. When I found a Remington large primer with two anvils I realized it was time to change. Also I have found one with no anvil. I still have both.

95
Star Lubricator & Resizers / Re: PROPANE FURNACE
« on: December 29, 2011, 08:49:26 pm »
You might have to take the valve assembly out of the propane tank , make a fixture to use that you can support the burner and lead pot with, and feed it from one of the idiot proof tank with a hose.

96
Star Reloaders / Merry Christmas
« on: December 23, 2011, 05:39:16 pm »
Merry Christmas to all

97
Star Reloaders / Re: BRASS POWDER HOUSING SPACER
« on: December 08, 2011, 10:31:35 pm »
I have a new in the box 1/2" Star charge bar(14.8 gr-2400) that was delivered with spacers that are either aluminum or white metal not brass and I also have several other sets that are the same. I also have a 5/8 charge bar housing that is stamped 5/8" not OOOO.

98
Star Reloaders / Re: #21P SET SCREWS
« on: December 04, 2011, 05:31:45 pm »
AT 40 TPI ( threads per inch ) I do not think that it is NC .

99
Star Reloaders / Re: #21P SET SCREWS
« on: December 04, 2011, 10:02:24 am »
Check with FC 60 as he makes #21

100
Loading Data & Reloading Procedures / Re: 44 Mag powder Bar
« on: December 03, 2011, 07:56:03 am »
I have a 1/2" bar that is stamped 4227- 18 gr which will compute to about 18.6 -2400 .I do not know if the hole has been opened up. It measures about . 460".
I also have  a 5/8" bar stamped 296-22gr which will compute to about 19 gr 2400. This bar may have been opened up as it also measures .460".
I have not checked either to see what they throw.

101
Stars Want to Sell/Want to Buy / Re: Decapping pin assembly for .45
« on: November 28, 2011, 08:15:36 pm »
PM  FC60 , He makes them.

102
Loading Data & Reloading Procedures / Re: SWC overall length
« on: November 28, 2011, 07:47:28 pm »
Ken
Take the recoil spring out of the pistol and also take out the firing pin. With this done put a magazine in the pistol and slowly move the slide foward. You will be able to  see in slow motion how it functions.If the round pops up to soon you have mag problems. When I shoot I have about 1/16 " lead out beyond the case and I have never used any crimp. I just try to get the case wall back to straight with the crimp die. My pistols function flawlessly with both the short 185 swc and the 200 swc.

103
Loading Data & Reloading Procedures / Re: SWC overall length
« on: November 27, 2011, 10:16:40 pm »
IF (remember that I said IF) the magazine does not release at the right time a swc is going to jam.  The mag must release just momentarly before the extractor is over the round.  The round underneath or the follower should cause the round to pop up, the extractor catches and the round goes home.  Remember thet the 1911 was designed for round nose bullets. I have a specially altered pair of pliers that I can use to move the release point back.

104
Stars Want to Sell/Want to Buy / Re: die and expander nuts, # 17 & 19
« on: November 27, 2011, 10:05:09 pm »
He did about as good a job IN ENGLISH as is needed , now if you need some kind of special dialect then-----------------

105
Star Reloaders / Re: 9 m/m lifetime
« on: November 20, 2011, 03:33:20 pm »
Dave

Mine appears the same with the carbide insert protruding out the bottom. I did not know that Star ( Lifetime ) high luster chrome plated their dies

Pages: « 1 2 3 4 5 6 7 8 9 »
anything