Messages

1

Stars Want to Sell/Want to Buy / Star tool head 9mm dies

« on: August 05, 2018, 11:51:59 am »

Star tool head, lifetime 9mm sizing die ,expander , seating and a Lee factory crimp die. Tool head crimp hole drilled out
to 7/8x14. Powder slide housing, one powder slide
 Also include 9mm shell plate. All in very good condition,just don't need now replaced 9mm loading with Dillon

$500 delivered
Right now down to only cell phone for internet, can send photos via text
contact
yz(four ,two ,six ,two) k  at aol dot com   email  also  listed on member page

PO money order or might be able to do  PayPal

2

Survey Says... / Re: Camp Perry

« on: March 26, 2016, 07:22:36 pm »

Everyone should have at least two Star machines,I went to Perry from 1970 to 1976 with the pistol ,what a great time,the hut ,that long walk in the morning and those powdered eggs in the mess hall. I returned in 1983 and shot rifle for several years this time with my wife and now two sons, but still had a great time. Perry is a great place it can build you up one moment and then slap you in the face the next .
After retiring I started to look for bullseye matches in Florida and found that most were gone. I then started to shoot some USPSA and ICORE as I could shoot almost every weekend and not drive too far. Now I woke one morning about 6 weeks ago  and thought I should look into shooting bullseye again ( could be my ADHD) .So I pulled out some of  my old stuff  .sent in my entry and might even start to do a little practicing. Hope to see some of you there,but will not be staying a the hut (if they are still there) ,Wife says "Once was enough " 

3

Star Reloaders / Tool head die holes Question??

« on: February 16, 2016, 07:58:06 am »

From looking at the tool head it appears that the sizing hole and taper crimp hole can be opened to 7/8x 14 (standard die size )
Is enough room to open up the seating hole to allow the use of a micrometer type seating die??
Any info helpful
Thanks

4

Stars Want to Sell/Want to Buy / WTB shell plate and dies for 9mm

« on: September 23, 2013, 03:12:20 pm »

Need shell plate and dies for 9mm

  email:bcd11122(AT)aol.com
 

5

Stars Want to Sell/Want to Buy / Decapping stem for Perfection 38 special carbide die

« on: March 07, 2013, 07:33:59 pm »

As stated I need a decapping stem for a  Perfection 38 special  carbide sizing dieand
I  also would like to find a new or near new LifeTyme 38 special carbide sizing die

Thanks for looking

Bob   bcd11122(AT) aol (DOT) com

6

Survey Says... / Re: Dave Wilson (fc60) Master Machinist

« on: July 12, 2012, 05:57:30 pm »

Dave made me a complete set of dies and did some tool head modifications and I can tell you that his work is outstanding
 it looks better that the original Star parts

He knows Star reloaders inside and out,,if you need parts that he cannot make, I am sure he will know where to find it

Thanks again Dave


Bob Settle

7

Star Reloaders / Set up for 38 short colt

« on: May 14, 2012, 04:38:31 pm »

 I need to start loading for 38 short colt . Has anyone here set up their star for this ? On most of the other sites they are using Dillon and from what I see they use a mix of different caliber dies . The 38 sc is basically a shorter 38 special case . I can use a regular 38 special resizing die, shorten  an expander and I guess I could also just shorten a seating and taper crimp die. I could also use an adjustable  powder slide ,but I cannot seem to locate one.  I have several 38 special tool heads and a few spare dies .  Any info would be helpful . Thanks

8

Stars Want to Sell/Want to Buy / WTB 45acp taper crimp die

« on: February 29, 2012, 04:56:25 pm »

Need 45 acp taper crimp die for star reloader

bcd11122(at)aol(dot)com

Thanks