1
Star History / Re: Star Machine Works, the Next Chapter
« on: November 17, 2014, 10:05:02 am »
This is Outstanding News for anyone with Star Tooling. Congratulations Bruce.
News:
Your active membership and involvement is what makes this forum work. Thank you very much!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Stars Want to Sell/Want to Buy / Wanted, Chevron Case Master
« on: February 13, 2013, 12:47:45 pm »
Hello Group; I am looking for Chevron Case
Masters, i would like Two. Please message me on this forum
With your price per unit plus shipping.
Thank You.
Masters, i would like Two. Please message me on this forum
With your price per unit plus shipping.
Thank You.
3
Stars Want to Sell/Want to Buy / Re: i want a used star sizer for $200 or less
« on: November 05, 2012, 10:03:40 pm »
Reality , you may locate a star machine
on a auction or in the want adds ..
I have - some have needed LOTs of $ to bring
up to usable condition . Others were missing many
parts.
There are fellows here that are in tune
with the current value of these machines.
You may consider doubling your minimum or more.
These are hand made machines , Not Lee's
I can only hope this helps you join the Star
Family of Star Tool users.
on a auction or in the want adds ..
I have - some have needed LOTs of $ to bring
up to usable condition . Others were missing many
parts.
There are fellows here that are in tune
with the current value of these machines.
You may consider doubling your minimum or more.
These are hand made machines , Not Lee's
I can only hope this helps you join the Star
Family of Star Tool users.
4
Stars Want to Sell/Want to Buy / Re: WTB - Powder Drains
« on: October 01, 2012, 08:16:05 pm »
I would like to order Two of your powder drains. Please PM
Me here so we can make arrangements.. Thanks.
Thank You, Two Powder Drains arrived.. I'm out of town..will be needing
A few more.. Soon ...
Me here so we can make arrangements.. Thanks.
Thank You, Two Powder Drains arrived.. I'm out of town..will be needing
A few more.. Soon ...
5
Star Reloaders / Re: CPM Reloaders - Looking For Information
« on: June 16, 2012, 10:33:32 pm »
I have a CPM, .45ACP... Had to have bushings made for the powder slide.
Paid 85$ at Gunshow . It works Great!
Paid 85$ at Gunshow . It works Great!
6
Stars Want to Sell/Want to Buy / Re: Roller Handle & Powder Magazine
« on: June 16, 2012, 03:32:50 pm »
I am still looking for a powder magazine
in usable condition. Thanks....
in usable condition. Thanks....
7
Stars Want to Sell/Want to Buy / Powder Magazine
« on: May 28, 2012, 07:46:19 pm »
Wanted, One standard or top quality modified powder mag. With cap in good condition.
Powder Mag is for personal use not resale..
Cash postal money order or Certified funds sent upon request.
Thank You for your interest..
Powder Mag is for personal use not resale..
Cash postal money order or Certified funds sent upon request.
Thank You for your interest..
8
Stars Want to Sell/Want to Buy / Re: Owners Manual for Chevron Case Feeder Needed
« on: March 21, 2012, 05:10:04 pm »
PM in bound
9
Stars Want to Sell/Want to Buy / Re: Parts Wanted to buy
« on: February 22, 2012, 07:21:33 am »
BTT
10
Star Reloaders / Re: Crank shaft bearing
« on: January 11, 2012, 09:14:39 pm »
Hello Group; FC 60 is Right on the money. I located two star base units without the matched Crank Shaft Assy.... With the help from another forum member I located two crankshaft assy`s on Gun Broker... The #7 tappered reamer did the trick slow and easy. Locked the crank shaft into alignment on the main shaft with a allen screw after installing the links between the crank assy and the tool head. A new #7 tappered pin was then marked and easy to cut to the right length. Total cost for two tappered pins was 16.00, borrowed the reamer.....
11
Stars Want to Sell/Want to Buy / Parts Wanted to buy
« on: December 27, 2011, 07:53:57 pm »
Hello Group; I am looking for a few Star parts. Part #63 Links, need two. Operating Handle, roller type or standard, need one.
Looks matters little as long as items can be used. Please advise Via PM of part # and price wanted cash- postal money order.
Thanks for the help with this. Jon
Looks matters little as long as items can be used. Please advise Via PM of part # and price wanted cash- postal money order.
Thanks for the help with this. Jon
12
Stars Want to Sell/Want to Buy / Re: Rebuilt Powder Magazines
« on: December 12, 2011, 10:51:25 pm »
Quick turn around time and a Top Notch job!!! I am very happy with all three. Thank You.. JP
13
Loading Data & Reloading Procedures / Re: Difficult primer seating
« on: November 18, 2011, 06:41:27 pm »
When most of us buy large amounts of brass is can be interesting to find that 45 ACP as we all know has some strange cousins..... 45 GAP, also has a small primer pocket... Locks up the press RFN. At that point it is clear what G A P stands for... I just wonder, Why would anyone put themselves in a position that Ammo for a side arm would be a non standard hard to get in a pinch, 45 ACP SHORT just my thoughts . JP
14
Stars Want to Sell/Want to Buy / 9MM Star Sizer Die, Shipped to new home
« on: November 17, 2011, 07:51:37 pm »
Shipped to new home, Thanks for looking
15
Stars Want to Sell/Want to Buy / Re: Hulme top plate
« on: August 02, 2011, 06:12:13 pm »
Hello Group; You may need a modification to your hulme feeder itself other than the top unit for 44mag as many will not feed the larger rimmed cases ( 44, 45LC,).... The mod can be done by any good machine shop. Other folks may have a better idea, but this worked well for me in 44 & 45LC. P