Messages

1

Star Reloaders / .44 magnum powder charge

« on: March 25, 2023, 03:54:39 pm »

would like to throw 22 grains of 2400 on the Star.Is there a taller powder bar that will do it?

2

Stars Want to Sell/Want to Buy / Re: WTB: vintage indexer as shown in the pic

« on: March 27, 2019, 03:50:08 pm »

I had one of these it is a Phelps product.It worked fine until the spring broke.I used a spring loaded belt loop type key holder with much better results.

3

Stars Want to Sell/Want to Buy / Re: .38/.357 bullet seating die and seating punch

« on: March 03, 2017, 12:15:22 am »

Have acquired two ,thank you

4

Stars Want to Sell/Want to Buy / Re: WTS Lee Case Feeder Adapters

« on: February 24, 2017, 10:52:33 pm »

Hello Bruce do you have a .38 cal. Bullet seater and punch?

5

Stars Want to Sell/Want to Buy / .38/.357 bullet seating die and seating punch

« on: February 21, 2017, 03:51:05 pm »

I need a .38/.357 bullet seating die

6

Stars Want to Sell/Want to Buy / Moon / Ray Vin case kicker

« on: November 07, 2015, 02:05:58 pm »

Would like to buy a Ray Vin case kicker,I have tried their site with no luck.Appreciate advice.

7

Star Reloaders / MA system case feeder spring install

« on: April 13, 2015, 12:40:51 am »

I was fitting a new tube to my MA case feeder and removed the screw on the side,the spring popped out and I have not figured out how to put it back in.Any help greatly appreciated

8

Stars Want to Sell/Want to Buy / Re: Need a .38 RN seating stem and a 9mm powder drop tube

« on: March 08, 2015, 01:02:59 pm »

I would like the .32 powder drop please.

9

Stars Want to Sell/Want to Buy / Re: Need a .38 RN seating stem and a 9mm powder drop tube

« on: March 08, 2015, 01:01:52 pm »

like to have them asap ,send me a total please.Thanks

10

Stars Want to Sell/Want to Buy / Need a .38 RN seating stem and a 9mm powder drop tube

« on: March 07, 2015, 08:49:03 pm »

I need a .38 RN bullet seating stem and a 9mm powder drop tube.

11

Stars Want to Sell/Want to Buy / powder drop tube 9mm

« on: October 05, 2014, 09:34:13 pm »

I damaged the drop tube in my 9mm tool head,flared it on a full metal jacket round nose.Any available somewhere?

12

Stars Want to Sell/Want to Buy / Re: WTS Hulme Top Plates M3, M3A and 9MM, .380, 32 S&W Long, 40 S&W

« on: October 05, 2014, 11:04:32 am »

will any of the standard plates function with .30 carbine?

13

Star Reloaders / Re: primer feeder misalignment

« on: June 30, 2014, 07:34:20 pm »

I was sucessful by putting a piece of brass tubing over the pin on the primer slide that the cam bears against.Corresponding sizes of brass tubing can be stacked on for added thickness

14

Star Reloaders / Re: primer feeder misalignment

« on: April 22, 2014, 11:39:15 am »

I have thourouly cleaned it to no avail.

15

Star Reloaders / Re: Top PLate

« on: April 20, 2014, 01:23:30 pm »

 Who makes a top plate for the Hulme in .44 mag?