Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - teg2650

Pages: 1
Stars Want to Sell/Want to Buy / Complete 38 Special tool Head SOLD
« on: August 01, 2022, 10:10:55 am »
Tool head complete with Lifetyme sizing die, 2.5 BE powder slide
Powder Magazine
38 Special Shell plate
Primer magazine tube and primer follower rod
5 primer pick up tubes
3 primer slides, 2 new and 1 used
primer punch and primer bushing
Extra lifetime sizing die, seating die and expander plug
Send a message with email address for pictures
$250 firm shipped in a USPS flat rate Priority box
Tom Ginovsky

Stars Want to Sell/Want to Buy / Re: Star Press For Sale
« on: September 09, 2021, 04:45:47 pm »

Stars Want to Sell/Want to Buy / Re: Bullet sizer
« on: August 03, 2020, 09:37:51 am »
On the cast boolits web site there is a person who makes the 3 piece set you are looking for and sell them for just under $30, I bought one from him a few years back. On EBAY they sell for at least twice that.

Stars Want to Sell/Want to Buy / FS PHELPS UNIVERSAL 38&45 LOWER PRICE
« on: March 18, 2019, 09:54:34 am »
1-Phelps Universal with Hulme case feeder set up in 38 special.
2-Spare tool head set up in 45ACP, shell plate,large primer parts,primer magazine.
3-OO powder housing & cover plate on both heads and 4 fixed powder bars  .
PM a email address for pictures. USPO payment, and I ship FEDEX.
$400 plus shipping, send a zip code and I will give a shipping price.
Tom Ginovsky

Stars Want to Sell/Want to Buy / New 45ACP Tungsten Sizing Die SPF
« on: January 15, 2019, 04:20:44 pm »
New in the box 45ACP R.L. Shockey "PERFECTION" sizing die for Star Reloader. $50 delivered, US only. PM for picture.
Tom Ginovsky

Loading Data & Reloading Procedures / Re: Charge Bars?
« on: February 07, 2018, 10:21:45 am »
 Hornady made a pistol powder measure that used/made the powder bushing you are talking about, it is 1/2 inch tall, I don't think they make the bushing any more. I have their 1986 catalog with a powder chart, PM me a email address and I will send you a picture of it. It shows #5 bushing to be 3.7 grains of bullseye. Bruce in NJ who owns Star makes the bushings.

Star Reloaders / Re: Backwards Primers
« on: August 24, 2017, 11:01:49 am »
I am the third owner of my Star Universal 45ACP which I purchased in the early 1980s. When it came to me the owner claimed it to have loaded approx 1 million rounds. A few years after I got it there started to be issues with skipped primers, I finally looked down the primer tube with light on the other end and could see wear in the tube. Replaced the tube at least 20 years ago and it has been fine since. You may have a worn spot in your primer magazine tube that is allowing a primer to flip from time to time. I also own a Star Universal (4 years) in 38 spec and the primer magazine tube has had primers(Winchester)  get stuck in it a few times now.
Tom Ginovsky

Star Reloaders / Re: Hulme Case Feeder
« on: April 01, 2017, 04:38:13 pm »
Contact Bruce at Star Reloaders and see if he has one to sell or if you have the time watch EBAY for one, I bought two there over the last few years.

Survey Says... / Re: ;part;s list
« on: December 25, 2016, 11:53:43 pm »
When you open this web site at the top click on manuals instead of discussion forum, scroll down and click parts list then scroll down

Stars Want to Sell/Want to Buy / For Sale-Clone Hulme Case Feeder/SPF
« on: April 04, 2015, 02:33:20 pm »
Clone Hulme Case Feeder, bought from Gerald Chainsaw a few months ago and just got a real Hulme so the copy is no longer needed. $60 Shipped. USPO only. Send PM with your email for pictures. Thanks, Tom Ginovsky

Stars Want to Sell/Want to Buy / For Sale/SOLD
« on: February 17, 2015, 04:08:31 pm »
 Star tool head with 38 special perfection dies, shell plate, 3 grain bullseye 00 powder slide, powder slide cover and base, small primer punch and bushing, primer pick up tube, primer magazine tube, shell floor plate bushing. Everything needed to convert a Star universal to 38 special. $325 shipped. I could not figure out how to post pictures so send a message and I will email them.
 I purchased a Star Universal set up for 45acp and 38 special, these are the parts I do not need.(already have a universal in 38 spec)
Tom Ginovsky

Stars Want to Sell/Want to Buy / Re: WTB
« on: August 10, 2013, 11:28:49 am »
 Parts arrived today, they look to be new, much better then I expected to find.

Stars Want to Sell/Want to Buy / Re: WTB
« on: August 08, 2013, 08:46:35 pm »
No problem, thanks for the update.

Stars Want to Sell/Want to Buy / WTB
« on: August 05, 2013, 11:40:18 am »
Need two parts for Star Universal, #24 primer punch for large primers and #26 primer punch bushing for large primers. Please send info to me as a message.

Stars Want to Sell/Want to Buy / FOUND ONE
« on: July 16, 2013, 09:33:26 am »

Found one, thank you to all who replied.

Pages: 1