Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - varmintpopper

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 »
1
Stars Want to Sell/Want to Buy / Re: WANTED, Need 9mm Luger Shell plate
« on: September 18, 2021, 09:47:53 pm »
Thanks Kenn
I have a new one ordered, But it's going pretty slow out there. Was hoping someone had a used one they would part with.
I'm considering modifying a 380 plate to fit 9 mm. or just machine a plate for myself. I have a mill.


Good Shooting

Lindy

2
Stars Want to Sell/Want to Buy / WANTED, Need 9mm Luger Shell plate
« on: September 17, 2021, 07:56:15 pm »
Need "9mm Luger" Shell Plate,
Appreciate all leads.

Good Shooting

Lindy

3
Stars Want to Sell/Want to Buy / Re: WANTED, 9mm dies and shell plate
« on: August 10, 2021, 05:13:50 pm »
Still looking for 9mm Dies and Shell plate !

miltonetime(at sign)aol(dot) com


Good Shooting

Lindy

4
Stars Want to Sell/Want to Buy / Re: WANTED, 9mm dies and shell plate
« on: July 22, 2021, 11:41:10 pm »
  Smokie 
PM sent, check Your Messages please.

Good Shooting

Lindy

5
Stars Want to Sell/Want to Buy / Re: WANTED, 9mm dies and shell plate
« on: July 21, 2021, 10:37:13 pm »
Still looking for 9mm setup
especially the shell plate !

6
Stars Want to Sell/Want to Buy / WANTED, 9mm dies and shell plate
« on: July 12, 2021, 10:31:07 pm »
Greetings
Anyone out there have a set of 9mm Luger dies and shell plate (For a universal) For sale or trade ??
#15  Sizing die with de-capping pin assembly. Carbide would be nice.
#16  Shell expander plug.
#18  Crimping Die
#13  Shell plate 9mm Luger

You can P.M. here on the forum or By Email: miltonetime(at sign)aol(dot)com
Looking forward to Your replies.

Good Shooting

Lindy

7
Stars Want to Sell/Want to Buy / Re: Trade 9mm Star tooling
« on: June 18, 2021, 09:23:02 pm »
Hi Gerald

Private Message Sent To You

Good Shooting

Lindy

8
Stars Want to Sell/Want to Buy / M.A. Systems Bullet feeder
« on: June 10, 2021, 05:03:32 pm »
Looking to buy or trade for another M. A. systems bullet feeder for a Star re-loader
Must be functional.

miltonetime (at sign) aol (dot) com

Or : send a PM

Good Shooting

Lindy

9
Star Reloaders / Re: DIY case kicker
« on: March 26, 2021, 09:41:37 pm »
You can use a taper crimp die in the last station if desired but it must clear the wire that cams the finished cartridge off the base plate. The bullet feeder was made by "M-A Systems Inc." Located in Pryor Oklahoma. They are still an active Manufacturer But no longer make the bullet feeder.

Good Shooting

Lindy

10
Star Reloaders / Re: DIY case kicker
« on: March 26, 2021, 12:11:31 am »
https://imgur.com/RhC0IJk
Check out the system I use for all My Stars.
No moving parts, works without fail.

Good shooting

Lindy

11
I always thought the hole was a gas escape hole in case a cartridge got set off at that station.

Good Shooting

Lindy

12
Stars Want to Sell/Want to Buy / Re: Wtb rayvin star case kicker
« on: February 06, 2021, 01:02:08 am »
Greetings Kyle
Welcome !
Email address not allowed on this forum. BUT, You can hide an Email address like This sample:

miltonetime(at sign)aol(dot)com   

This should work to hide Your own Addy.

Good Shooting

Lindy

13
Loading Data & Reloading Procedures / Re: 357 magnum load data question
« on: January 16, 2021, 12:47:03 am »
Mike
Your Question: I don't recall ever loading 7 grains of Bullseye for The 158 gr LSWC in 357 mag, I think that would be a little to hot.  Never had to get to 7 grs.
When developing a load for 357 mag using Bullseye I normally start with the suggested start load in "Alliant Powder reloading guide" and work up.
4.8 gr of Bullseye behind Your 158 LSWC should give a velocity of around 940 feet in a 6 inch barrel. Use Your 5 gr powder slide, load a dozen and give them a try. check for over pressure signs, check for leading, leading near the forcing cone  will indicate you need to increase the amount of powder, leading near the muzzle indicates high pressure. and then start tweeking the powder charge for accuracy.
I bought My first Star loader in 1956 "still have it" and a few more.

Good Shooting

Lindy

14
Loading Data & Reloading Procedures / Re: 357 magnum load data question
« on: January 14, 2021, 11:57:46 pm »
My Bad ,,, Typo,,, Ment to say 158 gr

15
Loading Data & Reloading Procedures / Re: 357 magnum load data question
« on: January 14, 2021, 08:17:52 pm »
Using the 148 grain SWC You have on hand, I suggest a starting load of 4.8 grains of Bullseye, watch for leading near the forcing cone, if it leads, try increasing the powder by .5 grains until leading stops. Don't exceed  7.0 grains.
Use this suggestion at Your own risk ! 

Good Shooting

Lindy

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 »