Messages

136

Loading Data & Reloading Procedures / Re: HP JACKETED BULLETS

« on: October 31, 2011, 12:09:58 am »

I have a M16 with a 9mm barrel (Olympic Arms), also other calibers....
Suppose I could use them for it...

137

Loading Data & Reloading Procedures / Re: HP JACKETED BULLETS

« on: October 30, 2011, 11:34:36 pm »

varmintpopper

Are .354 Bullets for 9mm..

138

Loading Data & Reloading Procedures / HP JACKETED BULLETS

« on: October 30, 2011, 09:03:10 pm »

Found in my Stash, some jacketed HP bullets...

They weigh approx. 135grs.

and mike:

Approx .354

Can I use these to load .38 Super..

It's a Caspian 1911 I put together.....   It has a Caspian Barrel.....

139

Stars Want to Sell/Want to Buy / Re: WTS 44mag/special die

« on: October 30, 2011, 01:25:01 am »

Dave
I got a Upside-Down One also...

140

Stars Want to Sell/Want to Buy / Re: WTB 44 mag Seater die, expander and powder measure

« on: October 29, 2011, 09:58:59 pm »

Barrel tester, Richard Daniels is a source for all sizes of Brass Powder Slide, also
adjustable Powder Slides......

'0' ---------1/4" - .250
'00' --------5/16" - .312
'000' -------1/2" - .500
'0000' ------5/8" - .625

141

Star Reloaders / Re: STAR WOOD HANDLE

« on: October 25, 2011, 04:16:54 pm »

Thanks 'varmintpopper'

Found a exact copy of the Handle on McMaster-Carr..

#4318A3  -  $2.18 each  

If anybody is concerned, the markings on one of my Star Handles, wood part, is:

LUTZ FILE & TOOL CO.
CINT.O.

That's what is marked on the Wood Handle from McMaster-Carr.........

Now you know said GI Joe

142

Star Reloaders / STAR WOOD HANDLE {Found a Source-CHECK IT OUT}

« on: October 25, 2011, 03:20:04 pm »

I'm looking for a source for the Wood handle for the Star Press..........
Wood only..

Anybody have a source..

143

Star Reloaders / THREAD SIZE FOR #20 & 20U

« on: October 21, 2011, 11:56:58 pm »

I show 2 sizes::

5/16"-32
3/8"-24

My dies are 5/16-32, is this #20U size or #20...??

144

Stars Want to Sell/Want to Buy / Re: HULME BOLT

« on: October 18, 2011, 06:33:04 pm »

OK, I'll do that.........

Thanks everybody.........

145

Stars Want to Sell/Want to Buy / HULME BOLT

« on: October 18, 2011, 12:24:43 am »

Got one more Hulme to install, BUT, I need the Bolt to install it to the #12U Base..
Anybody help me out..

It's  5/16"- 24 x 7/8"

146

Star Reloaders / Re: Hulme Case Feeder

« on: October 17, 2011, 09:10:20 pm »

YES HE DOES..
(Barrel tester) Richard Daniels

WELL WORTH IT..

*I also have one*

147

Star Reloaders / CRANK SHAFT BEARING & TOOL HEAD

« on: October 14, 2011, 01:31:59 am »

I'm inquiring about these two Holes.............

A hole in the TOOL HEAD on the left side is un-threaded and about 3/4" down
from the top of the tool head........The Hole is Just below the Key, you would
have to tap the Key down to utilize that hole to remove the Key, these holes are
on my Star Tool Heads........
The other screw hole I'm referring to is above the TAPER PIN hole at the rear of
the CRANK SHAFT BEARING, which is threaded.............

ANYBODY KNOW WHAT THESE HOLES WERE USED FOR

148

Star Reloaders / FORUM UP-DATE

« on: October 12, 2011, 06:33:39 pm »

Hey Guys,
When is next week, it's been 2 weeks now.....Looking anxiously to seeing the NEW Format.................

QUOTE:    Our forum software will be upgraded to the newest SMF 2.0 next week.

149

Star Reloaders / SMALL SCREW & WASHER UNDER THE STEEL BASE

« on: October 02, 2011, 08:24:53 pm »

Below is the Information about the small screw & washer under the Steel Base

Info:
This Screw & Washer is used to Prevent the #24 Primer Punch from dropping below the
#12/12U Steel Floor Base, thus, not letting the Press lock-up.....

Specs:

SCREW:
Slotted Fillister = 6-32 x 6/32"

WASHER:
Diameter = .375 OD
Screw Hole = .136"
Thickness = .038 varies

150

Star Reloaders / Re: INSTRUCTIONS FOR the MA CASE FEEDER

« on: September 30, 2011, 10:08:04 pm »

Thanks angus6