Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - tony barone

Pages: « 1 2 3 4 5 6 7 8 9 »
31
Star History / Re: Star Machine Works, the Next Chapter
« on: November 19, 2014, 01:33:47 pm »
Bruce makes superb products and all Star owners should be elated.

32
Stars Want to Sell/Want to Buy / Re: collator
« on: November 19, 2014, 01:29:43 pm »
Why not use the Dillon.

33
Stars Want to Sell/Want to Buy / Re: WTB: Primer tube, primer pick up tubes
« on: February 28, 2014, 07:10:33 pm »
Bruce makes parts as good if not better than original Star parts.

34
Star Reloaders / Re: Indexer
« on: February 04, 2014, 09:49:15 pm »
Loading 500,000 rounds on a manual machine is quite an accomplishment.

35
Star Reloaders / Re: Indexer
« on: February 04, 2014, 02:14:06 pm »
I deprime and under size the cases on a 550 with a case feeder. The 550 gets pretty grimy after awhile and I very seldom have to clean the Star. I'll load 1000 rounds on the Star and just have to remove any residual powder with compressed air and the machine is clean. They don't make Stars anymore and whoever gets mine it will last their lifetime.

36
Star Reloaders / Re: Indexer
« on: February 01, 2014, 04:18:57 pm »
I purchased the MA System indexer when I bought my machine from Star in 1986 and have loaded 200,000 rnds. on it. The base is still relatively good  probably because I've never deprimed on it and the indexer doesn't seemed to have induced any wear. I just got another MA system indexer from E-Bay, why I don't know as they never wear out.

37
Star Reloaders / Re: Moon unit round flipper
« on: August 18, 2013, 02:35:10 pm »
Rangedog  how is that MA System bullet feeder working out? They are hard to find.

38
Star Reloaders / Re: Moon unit round flipper
« on: August 18, 2013, 02:02:06 pm »
How about removing some material from the inside of the flipper.

39
Star Reloaders / 38 Super die
« on: July 08, 2013, 08:18:16 pm »
Just received a 38 Super die from fc 60. Remarkable workmanship.

40
Stars Want to Sell/Want to Buy / Re: Seating Stem
« on: May 30, 2013, 09:21:23 pm »
Contact Dave Wilson fc60 he will do it for you.

41
Loading Data & Reloading Procedures / Re: Expander plug depth
« on: April 30, 2013, 02:16:23 pm »
I think that the expander was designed to also hold the case down while seating a primer to eliminate stress on the shell plate. I had to modify my expander in order to load 38 supercomp brass as it was bulging the base of the case. This may not be relevant to the question though.

42
Star Reloaders / Re: The Holy Grail of Star dies
« on: September 20, 2012, 07:42:54 pm »
I have to think of something that I need from Dave. His work is beautiful.

43
Stars Want to Sell/Want to Buy / Re: Small Primer Slide Needed
« on: September 17, 2012, 01:53:36 am »
Give Bill Cunningham a shout and he will help you out.

44
Star Reloaders / Re: Springs
« on: August 20, 2012, 03:14:55 pm »
Give Bill Cunningham a call at Star Machine Works.

45
Star Reloaders / Re: Would like to see full auto setups with stars
« on: July 21, 2012, 01:10:05 pm »
That is a great set up but I would not have the guts to make mine an auto drive as I'm more comfortable feeling the machine. You are also very mechanically inclined. Nice job.

Pages: « 1 2 3 4 5 6 7 8 9 »