Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ed looney

Pages: 1
1
Star Reloaders / Re: Star Straight Line? Caliber 30/06 with wilson dies
« on: December 18, 2014, 08:28:48 pm »
RPG LLC, 4418 Central Avenue SE, Albuquerque,NM 87108

2
Star Reloaders / Re: Case Indexer
« on: February 18, 2013, 06:19:34 pm »
I think you have a, SHELL PLATE INDEXER, No 100. Ed

3
Star Reloaders / Re: Help me identify these
« on: May 03, 2009, 07:49:57 pm »
Small and Large pickup tubes and primer magazine for CH re loaders. They could be used for other reloaders probably.

4
Star Reloaders / Re: Paul Jones
« on: May 14, 2008, 06:59:56 pm »
Try emailing at (saeco95867atsymbolyahoo.com) he will answer.

5
Star Lubricator & Resizers / Re: New Magna Sizer VS OLD Sizer
« on: March 31, 2008, 04:04:47 pm »
I cast 9mm, 357, 45ACP and 44's with SAECO molds, and have pushed them through nose first since the late seventy's or early eighty's with no problems.   ed

6
Survey Says... / Re: 45 ACP 'Major' loads in the Star.
« on: March 18, 2008, 09:32:54 am »
Pete, Amazon.com has the book by Waters, for about $45 to $50, a little pricy but well worth it. Go on Amazon and look up "pet loads".     ed

7
Star Reloaders / Re: Star Powder Tube Thread Size
« on: March 03, 2008, 09:32:37 am »
I don't have there mailing address but they are in Ohio, have a good web sit "CH4D". Look them up on the web has all the info for contacting them and a telephone number. They are real friendly people to deal with.  ed

8
Star Lubricator & Resizers / Re: Got my first Starr!!!
« on: November 29, 2007, 08:08:41 pm »
I have 2 old star lubber and sizer, use Magma dies in them with no problem.  Ed

9
Star Reloaders / Re: Shell plates
« on: August 10, 2007, 12:06:03 pm »
They made 380, 9mm, 38 spec. use for 357, 30 cal carbine, 44 mag, 45, and 223. These are the ones I have they might have made others, you cannot use 38/357 for 45 the opening is to small.  Ed

10
Star Reloaders / Re: How do you tell a Star from a copy?
« on: September 11, 2006, 11:35:20 am »
RB, I think you are right, I was not thinking at all. I just did some work on a Berdon tool head for a fellow and had my brain on something else.

11
Star Reloaders / Re: How do you tell a Star from a copy?
« on: September 11, 2006, 09:36:24 am »
Are these holes 1/2-27 or 11/16-24?

12
Star Reloaders / Re: How do you tell a Star from a copy?
« on: August 31, 2006, 11:57:12 am »
GO ON PAGE 2 OF THIS FORUM, CLICK ON OLDTIMER AND READ THE WHOLE THING, ROSS CHESLEY GOES INTO PRETTY GOOD DETAIL EXPLANING THE MACHINES, YOU MIGHT HAVE A STAR MACHINE WITH A PHELPS TOOL HEAD, EVERY THING I HAVE READ STAR PUT COLLARS ON THEIR HEADS (I HAVE 7 HEADS) THEY HAVE COLLARS, STAR DECALS ARE NOT OVAL THEY ARE RECTANGLE.

13
Star Reloaders / Re: How do you tell a Star from a copy?
« on: August 31, 2006, 09:17:52 am »
LOOK ON THE BOTTOM OF THE TOOL HEAD AND SEE IF THERE IS A COLLAR MACHINED ON IT (WHERE THE HEAD SLIDES UP AND DOWN THE SHAFT) STAR STAMPED THERE NAME ON TOP OF THE TOOL HEAD.

14
Star Reloaders / Re: Interesting Star Reloader on eBay
« on: March 07, 2006, 11:42:44 am »
THE ATTACHMENT ON THE CASE FEEDER LOOKS LIKE A SPRING CLAMP USED FOR CLAMPING PARTS WHEN GLUING, I WOULD LIKE TO SEE A BETTER PICTURE OF THE CASE FEEDER ALSO.

15
Loading Data & Reloading Procedures / Re: powder data
« on: December 20, 2005, 08:57:30 am »
Steve,  If you still need the powder volume comparison for BE slides let me know at [no e-mail]@.COM I have a chart & formula that JOHN PAUL JONES gave me and the ones that I have used work great. let me know. I will scan and send to you.   ED

Pages: 1