1
Star Reloaders / .44 magnum powder charge
« on: March 25, 2023, 03:54:39 pm »
would like to throw 22 grains of 2400 on the Star.Is there a taller powder bar that will do it?
News:
Thank you for reporting offensive and spam content. Help us keep the forums clean by using the Report to Moderator link at the bottom of the post.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Stars Want to Sell/Want to Buy / Re: WTB: vintage indexer as shown in the pic
« on: March 27, 2019, 03:50:08 pm »
I had one of these it is a Phelps product.It worked fine until the spring broke.I used a spring loaded belt loop type key holder with much better results.
3
Stars Want to Sell/Want to Buy / Re: .38/.357 bullet seating die and seating punch
« on: March 03, 2017, 12:15:22 am »
Have acquired two ,thank you
4
Stars Want to Sell/Want to Buy / Re: WTS Lee Case Feeder Adapters
« on: February 24, 2017, 10:52:33 pm »
Hello Bruce do you have a .38 cal. Bullet seater and punch?
5
Stars Want to Sell/Want to Buy / .38/.357 bullet seating die and seating punch
« on: February 21, 2017, 03:51:05 pm »
I need a .38/.357 bullet seating die
6
Stars Want to Sell/Want to Buy / Moon / Ray Vin case kicker
« on: November 07, 2015, 02:05:58 pm »
Would like to buy a Ray Vin case kicker,I have tried their site with no luck.Appreciate advice.
7
Star Reloaders / MA system case feeder spring install
« on: April 13, 2015, 12:40:51 am »
I was fitting a new tube to my MA case feeder and removed the screw on the side,the spring popped out and I have not figured out how to put it back in.Any help greatly appreciated
8
Stars Want to Sell/Want to Buy / Re: Need a .38 RN seating stem and a 9mm powder drop tube
« on: March 08, 2015, 01:02:59 pm »
I would like the .32 powder drop please.
9
Stars Want to Sell/Want to Buy / Re: Need a .38 RN seating stem and a 9mm powder drop tube
« on: March 08, 2015, 01:01:52 pm »
like to have them asap ,send me a total please.Thanks
10
Stars Want to Sell/Want to Buy / Need a .38 RN seating stem and a 9mm powder drop tube
« on: March 07, 2015, 08:49:03 pm »
I need a .38 RN bullet seating stem and a 9mm powder drop tube.
11
Stars Want to Sell/Want to Buy / powder drop tube 9mm
« on: October 05, 2014, 09:34:13 pm »
I damaged the drop tube in my 9mm tool head,flared it on a full metal jacket round nose.Any available somewhere?
12
Stars Want to Sell/Want to Buy / Re: WTS Hulme Top Plates M3, M3A and 9MM, .380, 32 S&W Long, 40 S&W
« on: October 05, 2014, 11:04:32 am »
will any of the standard plates function with .30 carbine?
13
Star Reloaders / Re: primer feeder misalignment
« on: June 30, 2014, 07:34:20 pm »
I was sucessful by putting a piece of brass tubing over the pin on the primer slide that the cam bears against.Corresponding sizes of brass tubing can be stacked on for added thickness
14
Star Reloaders / Re: primer feeder misalignment
« on: April 22, 2014, 11:39:15 am »
I have thourouly cleaned it to no avail.
15
Star Reloaders / Re: Top PLate
« on: April 20, 2014, 01:23:30 pm »
Who makes a top plate for the Hulme in .44 mag?