Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - NMBob

Pages: 1 2 »
1
Star Reloaders / Shockey progressive on ebay
« on: March 12, 2010, 04:59:42 pm »
Look at the Shockey progressive listed under "Star reloading."  As an item of academic interest, I'd like to hear if Ken Walters has ever seen one.  I assume it was built by Richard Shockey, the El Reno, OK. pistolsmith.

2
Star History / Re: Star on Ebay.
« on: December 09, 2009, 10:02:00 am »
Just logged in to see if anyone knew anything about that powder shut-off.  I was impressed too.

3
Survey Says... / Re: Camp Perry
« on: July 30, 2009, 12:49:25 pm »
I went with the New Mexico pistol team in 1984 and 1987.  It's a great experience, but I hate to fly with guns, and it's a long way from New Mexico by car.  And I can get in trips to Gunnison, CO and to the Whittington for the CO and NM state matches and regionals with just a few hours of driving.  The Whittington has a bullseye range roughed out but undeveloped and NM state match is shot on the PPC range.  This year's match is Sept. 12-13.  Visit the Whittington:  it's your range. 

4
Star Reloaders / Re: Starting Up
« on: April 15, 2009, 06:15:59 pm »
Above advice sounds right on the money.  I have found that CCI primers can be a bit harder than some to seat w/o damagine them.  Like the above folks, I like Wincester.  Assume you will be using a roundnose bullet for Single action cowboy type matches.  Back off the seating screw on the seating die and tighten gradually.  (This assumes that tool was set up for deep-seating wadcutters, as so many were for bullseye matches.)

NM Bob

5
Star Reloaders / Re: Paul Jones
« on: May 14, 2008, 12:08:36 pm »
Try coffeyn1 [at symbol] msn.com.

NMBob

6
Star Reloaders / Re: Star Universal Value?
« on: February 03, 2008, 05:05:20 pm »
The idea of selling the Star on Ebay with a reserve price of $450 (or 500 since it has a Hulme) or so is a good one.  It would also be a good idea to watch Ebay for a few weeks before listing.  And if your reserve is not met, don't despair.  The pool of bidders changes from week to week.  I've seen Hulme feeders go for 150, and there is one up now that is currently at 50 with several days to go.  The last few days always show a flurry of bidding, and sometimes bidders get carried away and bid far more than might have been expected.

I wish I'd encountered your Star before I got mine.  I had to add an O'Neill case feeder (an excellent version of the Hulme design) as well as a new carbide die, a safety cam, and a primer magazine.

   

7
Star Reloaders / Re: safety cam spring
« on: January 23, 2008, 12:35:22 pm »
Yep, I had never noticed that little pinprick.  Got the cam on, taper crimp die out, seating die readjusted to crimp, and cam filed slightly so it didn't collide with my case-feeder, a Hulme clone.  It works.

Thanks again.



8
Star Reloaders / Re: safety cam spring
« on: January 23, 2008, 11:12:13 am »
Thanks for the info.  I'm off to the garage.


9
Star Reloaders / safety cam spring
« on: January 21, 2008, 10:47:49 am »
Being new to progressive reloaders, I'm nervous about a double charge.  I got tired of peering into the case every time, so I just bought a safety cam for my Star, complete with spring.  I'm trying to install, but where do I attach the (short) free end of the spring so that cam will return to counter clockwise position and block the head from being pulled a second time w/o rotation?


10
Loading Data & Reloading Procedures / Re: Sticking Shell Plate
« on: October 20, 2007, 02:10:37 pm »
Cleaned and lubed, this time w. light coat of Anderol.  (Removed graphite lube in cleaning.)  Then readjusted the thrust nut.  Still hard to turn.  Then I examined the shell base locating straps--one was dragging.  Readjusted and now tool works fine.  I feel stupid, but relieved.

NMBob

11
Loading Data & Reloading Procedures / Re: Sticking Shell Plate
« on: October 19, 2007, 09:57:29 am »
Thanks, Tony.  What did you think about use of graphite vs. other lubricants?

NMBob

12
Loading Data & Reloading Procedures / Sticking Shell Plate
« on: October 18, 2007, 12:58:59 pm »
Just recently my shell plate has been harder to turn.  (Universal press, loading .45 ACP.)  I've tried raising the shell plate thrust nut, wiping the underside of the shell plate and thrust nut and the floor base under the shell plate.  Nothing looks scored or worn.  I sprayed a bit of powdered graphite on the floor base and on the top of the shell plate where it contacts the thrust nut.  Then I screwed down the thrust nut to a position very slightly looser than it had been.  I'm a fairly new Star user, but I've loaded some 500-1000 rounds before this problem surfaced.  I've got the original Star instruction sheet, but it seems to say nothing about lubing this area.

Does anyone lube this area with liquid lube?  I've felt the graphite is better since it will not attract primer grit, etc.

Thanks.

NMBob

13
Star History / Re: star tooling
« on: October 13, 2007, 03:25:31 pm »
Got my .45 sizing die the day I posted the above.  Well-made die, and it works fine.  My check was not cashed until the die was on its way.

NMBob

14
Star History / Re: star tooling
« on: October 12, 2007, 03:52:07 pm »
I have also placed a recent order (for a .45 ACP carbide die) and will report.

NMBob

15
Survey Says... / Re: receiving parts from the NEW Star
« on: September 21, 2007, 05:04:40 pm »
I've got a phone and a snail mail address, but have not been able to raise him.  What's his email address?

NMBob

Pages: 1 2 »