Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - cc656d

Pages: « 1 2 3 4 5 6 7 8 9 10 »
91
Stars Want to Sell/Want to Buy / Re: WTB Star toolhead with .45ACP dies
« on: September 25, 2012, 07:53:10 am »
All paperwork that came with a Star is on this site.

92
Stars Want to Sell/Want to Buy / Re: first 75 takes it...
« on: June 21, 2012, 07:24:24 am »
Dies appear to be 7/8 dies ( maybe RCBS ) but not Star.

93
Stars Want to Sell/Want to Buy / Dies?
« on: May 12, 2012, 07:39:04 am »
Does anyone here make 357 Sig dies for a Star?

94
Stars Want to Sell/Want to Buy / Re: parts for sale reloder
« on: May 06, 2012, 11:20:30 pm »
Sent message about 1/2" powder bar.

95
Stars Want to Sell/Want to Buy / Re: WTB - Tool Head Springs
« on: April 10, 2012, 10:58:27 pm »
I bought one a few years ago from a large hardware.

96
Star Reloaders / Re: CPM Reloaders - Looking For Information
« on: March 27, 2012, 06:37:50 am »
Gil Hebard sold them in the early 80's. Contact him , he might be able to help you.

97
Stars Want to Sell/Want to Buy / Re: WTB 5/8 powder bars
« on: March 07, 2012, 06:17:35 am »
You really should try Bill Cunningham [no e-mail]@ machine. Most recent price is $ 38 plus shipping.

98
Star Reloaders / Re: #50 Angle Lever Screw
« on: February 14, 2012, 06:49:35 pm »
pull it out and measure it, should not bee too hard

99
If you want to send an email , First look at profile as it may have the email address you need!

100
Star Reloaders / Re: NEW PARTS SOURCE FOR STAR MACHINE WORKS
« on: January 29, 2012, 04:41:47 pm »
If speed is the important factor you need a Camdex.

101
Star Reloaders / Re: NEW PARTS SOURCE FOR STAR MACHINE WORKS
« on: January 25, 2012, 08:18:02 pm »
Mr Waters
Each time that I have inquired availabity of parts , Mr Cunningham has been most prompt in answering and parts were available. ( Looked like old Star prices ) The worst thing that happened to Star was the association with Dillon.
By the way if you need a new in the box Star, I might be able to arrange it.

102
Stars Want to Sell/Want to Buy / Re: Wtb 49u angle
« on: January 22, 2012, 07:06:19 pm »
That part on EBAY is # 48 primer slide angle lever not the # 49u angle lever cam. They work together but they are not the same!

103
Stars Want to Sell/Want to Buy / Re: Phelps Star ????
« on: January 04, 2012, 09:12:24 pm »
The powder cam and the powder cam base do not look like any of the nine ( 9 ) Stars that I have, so I think thar the complete tool is a Phelps.

104
Stars Want to Sell/Want to Buy / Re: Phelps Star ????
« on: January 04, 2012, 04:53:31 pm »
The tool head on the tool is Phelps and the tool has non Star features which I think is a Phelps.

Thank you
Ricky

105
Star Reloaders / Re: CCI Large Pistol Primers getting sideways
« on: December 31, 2011, 11:24:12 am »
Problems can occur with primers . I purchased my first Star in [no e-mail]@. I used Remington primers for years but changed in the mid 80's . I loaded a lot ( bullseye shooting ) and Remington gotto the point of failure to feed in my Star. This would happen about once per hundred. It became a pain to clean the tool of loose powder. Remingtons Quality Controll was lacking. Upon examining the primers that gave problems I found that they were oval , not round and this was enough for the primers hagg up in the primer magazine. When I found a Remington large primer with two anvils I realized it was time to change. Also I have found one with no anvil. I still have both.

Pages: « 1 2 3 4 5 6 7 8 9 10 »