Recent Posts

Pages: 1 2 3 4 5 6 7 8 9 10
2
Nice pictures with good description.
3
Star Reloaders / Re: Indexer-Broken Spring
« Last post by fc60 on November 03, 2021, 07:32:07 pm »
Greetings,

A photo would help greatly.

Cheers,

Dave
4
Star Reloaders / Indexer-Broken Spring
« Last post by Star73 on November 03, 2021, 05:51:57 pm »
I have had/used 2 or 3 of these indexers over the yrs but have no paper on them. The unit operates by meaans of an arm pushing a slide w/ a "U" shaped end against a case moving it to the next position(Prime). The movement is accomplished by a short upstroke of the operating handle.

A small coil spring secures to the above U shaped part. This coil spring is broken... Can anyone provide info on this spring?? A supplier? Instructions to make one? 

Thanks,
Ron
6
Stars Want to Sell/Want to Buy / Re: M.A. Systems Bullet feeder
« Last post by Cousin Daniel on October 31, 2021, 06:37:25 pm »
Could you post pictures of the individual parts which make up the bullet feeder?

I would like to see if making one is out the question, just because it was cast does not mean it can't be machined from bar stock.
7
Complete setup for 44 Mag and 45 ACP with taper crimp.  Original owner; the machine has been carefully maintained with no damage or rust.  The bushing setup makes powder changes straightforward.  $1,450 package price includes everything below, with shipping & insurance to the lower 48 states.

1 - Universal Reloader (44mag) with Hulme Case Feeder, Powder Hopper, Primer Tube & Follower

1 - Loaded Toolhead and Shell Plate (45ACP) with Taper Crimp die and Base Plug

8 - Small Primer Pick-up Tubes
12 - Large Primer Pick-up Tubes

3 - 00 Powder Slides (4.0 Bullseye, 7.0 & 7.5 Unique)
3 - Powder Slides drilled for 1/2-inch bushings - one each 00, 5/8, 1/2
6 - 00 Powder Bushings
7 - 5/8 Powder Bushings
13 - 1/2 Powder Bushings

3 - Powder Slide Housing Bases 00, 5/8, 1/2
1 - Powder Slide Housing Cover
1 - Powder Slide Housing Shim set
4 - Powder Measure Spouts

2 - Large Primer Slides
1 - Large Primer Punch
1 - Large Primer Punch Bushing

2 - Small Primer Slides
2 - Small Primer Punches
1 - Small Primer Punch Bushing

2 - Primer Magazine Tubes (Large & Small)
2 - Primer Follower Rods
1 - Primer Punch Bushing Screwdriver
1 - Shell Floor Base Plug (for taper crimp die)
1 - Safety Cam Assembly
8
Stars Want to Sell/Want to Buy / star 00 powder bars, 3 pc small primer set
« Last post by ar dick harris on October 28, 2021, 12:30:58 pm »
Bars: 3.5 BE,2.7 BE, 2.5 BE priced at $30 ea + $9.20 shipping in flat rate box for 1,2 or 3 bars within the lower 48

Star small primer set,slide, punch and bushing, priced at $39.20 shipped within the lower 48.

Postal money orders to ar harris 515 E Bullard Ave., #120, Fresno, CA 93710

ardickharris one at sbcglobal dot net    559-432-2568
9
Stars Want to Sell/Want to Buy / Re: M.A. Systems Bullet feeder
« Last post by varmintpopper on October 27, 2021, 12:32:28 pm »
661mack

Thanks for the reply.
I'm not looking for the collator, Only the Bullet feeder.

Good Shooting

Lindy
10
Stars Want to Sell/Want to Buy / Re: M.A. Systems Bullet feeder
« Last post by 661MACK on October 27, 2021, 11:36:54 am »
Are you looking for the MA system bullet collator
Pages: 1 2 3 4 5 6 7 8 9 10