Messages

241

Star Reloaders / Re: STAR COVER

« on: May 30, 2011, 12:35:22 am »

Doc
Thanks for the Pic's. I'll have to get busy and get five of those ordered. I have been using plastic waste basket bags with a hole cut in the bottom for the handle to stick through. That works pretty good to keep the dust off the machines but no rust prevention.  Thanks again !

Good Shooting

Lindy

242

Star Reloaders / Re: hulme cleaning & maintenance

« on: May 27, 2011, 03:47:33 pm »

The Instructions for installing the Hulme case feeder has at the bottom of the page the following statement:

"THIS DEVISE IS LUBRICATED WITH LUBRIPLATE, KEEP IT LUBRICATED"

Good Shooting

Lindy

243

Star Reloaders / Re: STAR COVER

« on: May 25, 2011, 07:04:48 pm »

Thanks again for the update Doc.

Good Shooting

Lindy

244

Star Reloaders / Re: STAR COVER

« on: May 23, 2011, 01:36:46 am »

Thanks Doc, for the info

Good Shooting

Lindy

245

Star Reloaders / Re: STAR COVER

« on: May 22, 2011, 11:45:30 pm »

Doc
I'd like to see how well this cover fits the Star, could You Post a Pic or Two on the Forum ?
Thanks

Good Shooting

Lindy

246

Star History / Re: Cool old picture

« on: May 15, 2011, 09:22:25 pm »

The Salt Shaker was probably A storage bottle for either grease or oil to lube the machines. it would have a cap without holes in it and an Ice Cream stick or rod of some
sort to get the lube out and applied to the machines. But , That's only a guess on my part.

Good Shooting

Lindy

247

Star History / Re: Cool old picture

« on: May 14, 2011, 06:28:08 pm »

Yes that is a cool old picture, Thanks for posting.
I'm still using a Saeco lead pot identical to the one pictured.
Appears to be a portable casting and loading set-up, perhaps for a police range, looks 1950's or so.

Good Shooting

Lindy

248

Star Lubricator & Resizers / Re: STAR LUB/SIZ ACCESSORY

« on: May 05, 2011, 04:32:42 pm »

Could it be:   A roll/squeeze pin, with a cotter pin through the hole in the middle ?
                   Probable need a pair of Dyke's to get it out of there !   Anyway,,

Good Shooting

Lindy

249

Star Reloaders / Re: HOW TO POST PICTURES

« on: April 30, 2011, 10:02:03 pm »

Lindy's Test Pic

250

Star Reloaders / Re: A source for clear acrylic tubing

« on: April 13, 2011, 09:03:53 pm »

Address correction, It should read:   Plastics 2000
                                                   601 Bangs Ave
                                                   Modesto, Ca 95356

This dang keyboard of mine can't spell worth a darn !

Good Shooting

Lindy

251

Star Reloaders / A source for clear acrylic tubing

« on: April 12, 2011, 05:44:55 pm »

I don't know if these tubes are an exact match of the original Star tubes, But I have been useing them for years and they work just fine. Thicker walls are also available.
They come in 6 foot lengthes but must be cut into 36 inch lengthes for shipping. Current prices are subject to change.   Hope This Helps.
                   Inside diameters are:

                   1/8   $1.35 linear foot                             Plasics 2000                              Good Shooting
                   1/4   $1.35    "       "                               601 Bangs Ave.                              Lindy
                   3/8   $1.54    "       "                               Modesto, Ca. 95356
                   1/2   $1.54    "       "                                                            
                   5/8   $1.93    "       "                               209-577-2900
                   3/4   $1.93    "       "                        Fax  209-577-2905
                1 0/0   $2.32    "       "
                1 1/4   $2.85    "       "                                plastics2000.net

252

Star Reloaders / Re: Angle Lever Cam 49/49U

« on: April 04, 2011, 11:20:49 pm »

rbwillnj

Thanks for sharing that info, I remember that topic awhile back, and now I can quit scratching my head over it, because now I Know.

Good Shooting

Lindy

253

Star Reloaders / Re: SCREWS

« on: March 27, 2011, 11:27:22 pm »

Indeed the Setscrew is  10X32  by 3/16 long,  In the distance from where I measured it, to my computer keyboard it somehow changed from a 10 to an 8.

Good Shooting

Lindy

254

Star Reloaders / Re: SCREWS

« on: March 26, 2011, 10:54:54 pm »

Doc
The two Screws are common hardware items and should be available from any good hardware store.
The setscrew for the locating strap is a 8X32 slotted setscrew about 1/4 inch long.  Most setscrews made today are allen head.
The one that holds the handle on is a square head bolt 3/8X16 about 3/4 inch long.

Good Shooting

Lindy

255

Star Reloaders / Re: #82 SCREW

« on: March 23, 2011, 12:59:47 am »

askimball

The #82 screw is a fillister head 6-32
hope that helps

Good Shooting

Lindy