46
Star Reloaders / Re: Yellow Star Decal
« on: August 15, 2011, 02:30:52 pm »
First one i have seen, George.
News:
Your active membership and involvement is what makes this forum work. Thank you very much!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
47
Star Reloaders / Re: Chevron case feeder
« on: August 06, 2011, 05:01:31 pm »
I have tried both, and i will stick with the Chevron, George.
48
Star Reloaders / Re: TURRET ???
« on: August 04, 2011, 02:20:18 am »
Trust me Doc, you would not want to see them, George.
49
Star Reloaders / Re: TURRET ???
« on: August 03, 2011, 07:11:57 pm »
I have seen some of the old primer systems that held up to 1000 primers, if one ever goes off, you will wish you were somewhere else, George.
50
Star Reloaders / Re: So did I screw up ?
« on: June 17, 2011, 02:17:32 am »
Yes i have a 9mm plate, will measure it and email you, George.
51
Star Reloaders / Re: So did I screw up ?
« on: June 16, 2011, 09:34:35 pm »
My understanding was that the Chevron was discontinued, when several family members were in the shop, when a guy set off a large amount of powder, that killed and injured the owners in the blast, my Chevron feeders have always worked as good as any body elses, JMO, George.
52
Star Reloaders / Re: So did I screw up ?
« on: June 09, 2011, 01:32:45 am »
I used thin wall Auger Tubing, you want seemless tubing, the motors are available from Dayton Motors, the Micro Switch can be bought from most Auto Parts Stores, the shell plate is easy to make, but there is a part that secures the motor shaft to the shell plate, it should be machined to fit properly, Total cost on making mine was $65.00, George.
53
Star Reloaders / Re: So did I screw up ?
« on: June 07, 2011, 09:33:00 pm »
I misunderstood you, i thought you were putting it on a 650, if your using a Star, its ready to go, sorry about the confusion, i have 3 Chevron feeders on my stars, theres a couple diff shell plates for the Chevron, each will load several diff cases, i have also copied the Chevron and made 2 more, George.
54
Star Reloaders / Re: So did I screw up ?
« on: June 07, 2011, 10:53:45 am »
It will work just fine, with a little Retrofit , George.
55
Star Reloaders / Re: Loading .223 on Star
« on: April 28, 2011, 06:27:18 pm »
Larry, the bullet is held in place by neck pressure, and the standard links work just fine, if you want to crimp, you can do it in the seater die, George.
56
Star Reloaders / Re: calibration of bullets
« on: April 28, 2011, 10:30:16 am »
Theres a Guy on this forum that sells reconditioned ones, his name is Bruce, i have delt with him, always a pleasure to deal with Bruce, and he does not sell Junk, goes by rbwillnj on this forum, George.
57
Star Reloaders / Re: Plug part number 68
« on: November 13, 2010, 01:10:05 am »
Bruce is correct, theres more than one size in the Progressive Machines, George.
58
Star Reloaders / Re: Star Press Mounting Solutions
« on: September 11, 2010, 10:21:51 am »
Mine are mounted just like Rods, except they have Chevron case feeders, George.
59
Star Lubricator & Resizers / Re: Automatic Bullet Feeder??? What is this?
« on: July 06, 2010, 12:34:17 am »
Looks like a Bullet feeder, have no idea who made it, mabey Bruce will chime in here, looks to be well made, George.
60
Star Reloaders / Re: Hulme Case Feeder Instructions/Troubleshooting
« on: June 13, 2010, 09:44:33 pm »
Slide the piece off the rear of the feeder, spring will come out, remove the cam on the side of the feeder bolt, remove the bolt from body.