Author Topic: Hulme M2 top plate  (Read 9939 times)

0 Members and 1 Guest are viewing this topic.

angus6

  • Active Members
  • ***
  • Posts: 121
    • View Profile
Hulme M2 top plate
« on: September 01, 2011, 11:35:03 am »
What calibers are they for ?

rbwillnj

  • Global Moderator
  • ****
  • Posts: 1216
    • View Profile
    • Star Machine Works
Re: Hulme M2 top plate
« Reply #1 on: September 01, 2011, 11:38:49 am »
I had an M2 once upon a time, I thought it was the same as an M3.   I don't have one any more to compare.

Does the M2 have the recess for 38 special?
« Last Edit: September 01, 2011, 12:45:18 pm by rbwillnj »
Star Machine Works
Star, the original blue Press.  Made by machinist, not machines.
www.StarMachineWorks.com

MikeA

  • Active Members
  • ***
  • Posts: 53
    • View Profile
Re: Hulme M2 top plate
« Reply #2 on: September 01, 2011, 06:39:45 pm »
I found an M2 on one of my Stars set up for 45ACP.  I compared it to an M3 and they
are Identical. 
Semper Fi
MikeA

angus6

  • Active Members
  • ***
  • Posts: 121
    • View Profile
Re: Hulme M2 top plate
« Reply #3 on: September 01, 2011, 08:01:36 pm »
Finally found  where I set my calipers :o hole dia. was the only thing different on the feed end of things, M2 has a 20 thousand smaller hole. Top of the body is stepped down on both ends of the hole. This makes 3 different shaped tops so far

rbwillnj

  • Global Moderator
  • ****
  • Posts: 1216
    • View Profile
    • Star Machine Works
Re: Hulme M2 top plate
« Reply #4 on: September 01, 2011, 08:42:35 pm »
I'm thinking the M2 is just an earlier version of the M3, not a different type.
Star Machine Works
Star, the original blue Press.  Made by machinist, not machines.
www.StarMachineWorks.com

fc60

  • Active Members
  • ***
  • Posts: 480
    • View Profile
Re: Hulme M2 top plate
« Reply #5 on: September 02, 2011, 11:02:43 am »
Greetings,

Any possibility that one top plate has clearance for the 45 Auto Rim and/or the 45 Colt?

Cheers,

Dave

MikeA

  • Active Members
  • ***
  • Posts: 53
    • View Profile
Re: Hulme M2 top plate
« Reply #6 on: September 02, 2011, 11:53:31 am »
Hello to Dave,
The Marshall Enterprises info sheet, maker of the HULME automatic case feeder shows the following:
"The Mark III is equipped to handle five (5) calibers, .38 ACP, .45 ACP, .45 Auto Rim, .38 Special and .44
Special."
" The Mark IIIA is equipped to handle eight (8) calibers.  .38 ACP, .45 ACP, .45 Auto Rim, .357 Mag., .41 Mag., .44 Mag., .45 Colt Long, and .30 Cal. M1 Carbine."
I hope this helps.
Semper Fi
MikeA

angus6

  • Active Members
  • ***
  • Posts: 121
    • View Profile
Re: Hulme M2 top plate
« Reply #7 on: September 02, 2011, 08:29:52 pm »
This plate did come with a machine that was set-up for 38/357 - 41 mag

rbwillnj

  • Global Moderator
  • ****
  • Posts: 1216
    • View Profile
    • Star Machine Works
Re: Hulme M2 top plate
« Reply #8 on: September 02, 2011, 09:36:03 pm »
OK, but that's not a magnum top plate unless it's been modified.   I have had a number of M3 top plates that have been milled out to accept magnum cases.
Star Machine Works
Star, the original blue Press.  Made by machinist, not machines.
www.StarMachineWorks.com