Author Topic: Half the Mounting Holes Drilled Out to 3/8"  (Read 4069 times)

0 Members and 1 Guest are viewing this topic.

FOR_Star

  • Active Members
  • ***
  • Posts: 93
  • Star Universal owner since 1979
    • View Profile
Half the Mounting Holes Drilled Out to 3/8"
« on: June 24, 2021, 03:25:14 pm »
Acquired a new-to-me Star Universal.  Everything looks original and in good condition, but does need a good cleaning, fluff & buff, and lube.
I'm curious as to why a previous owner would drill out the two "front" mounting holes to 3/8".  Has anyone seen a mounting arrangement that needed the front holes opened up to 3/8"? Some sort of quick-disconnect arrangement?

Could make using a Ray-Vin indexer more challenging, I guess.
Warren
Fair Oaks Ranch, Texas
Star owner since 1979

rbwillnj

  • Global Moderator
  • ****
  • Posts: 1216
    • View Profile
    • Star Machine Works
Re: Half the Mounting Holes Drilled Out to 3/8"
« Reply #1 on: June 25, 2021, 07:55:06 am »
Sometimes people just don't have enough 1/4" bolts in the drawer.   I have seen several where the mounting holes have been enlarged.

Since only the two in the front mounting holes have been enlarged, I would guess it had something to do with mounting an indexer.
Star Machine Works
Star, the original blue Press.  Made by machinist, not machines.
www.StarMachineWorks.com

FOR_Star

  • Active Members
  • ***
  • Posts: 93
  • Star Universal owner since 1979
    • View Profile
Re: Half the Mounting Holes Drilled Out to 3/8"
« Reply #2 on: June 25, 2021, 04:55:11 pm »
Yeah, those pesky 1/4" machine screws. HaHa

Surprised the OEM Star mounting bolt wasn't a 17/64-28 UNS. (an attempt at a little SMW over-engineered humor)
« Last Edit: September 23, 2021, 03:05:04 pm by FOR_Star »
Warren
Fair Oaks Ranch, Texas
Star owner since 1979

FOR_Star

  • Active Members
  • ***
  • Posts: 93
  • Star Universal owner since 1979
    • View Profile
Re: Half the Mounting Holes Drilled Out to 3/8"
« Reply #3 on: September 23, 2021, 03:10:29 pm »
Any thoughts on a somewhat reasonable way to return these two holes to their original dimensions? (1/4" hardware, with countersink)
Warren
Fair Oaks Ranch, Texas
Star owner since 1979

Richard Hubbard

  • Active Members
  • ***
  • Posts: 6
    • View Profile
Re: Half the Mounting Holes Drilled Out to 3/8"
« Reply #4 on: September 23, 2021, 05:07:19 pm »
Just replace the base. 
Star Machine Works should have replacement bases.  At least they did when I inquired a few months back.

FOR_Star

  • Active Members
  • ***
  • Posts: 93
  • Star Universal owner since 1979
    • View Profile
Re: Half the Mounting Holes Drilled Out to 3/8"
« Reply #5 on: September 24, 2021, 02:13:01 pm »
Just replace the base. 
Star Machine Works should have replacement bases.  At least they did when I inquired a few months back.

That is one way.  I'm sure Bruce could fit a new base if I sent it back to him.

Does anyone know if the base is cast aluminum, or is it cast zinc-like metal similar to the powder slide housings?
And, if aluminum, could a welder experienced in aluminum welding close up the holes so they could be re-drilled and countersunk? (obviously, without FUBARing the base)
Bruce and/or Dave, any thoughts?

Thanks,
Warren
Warren
Fair Oaks Ranch, Texas
Star owner since 1979

Dan

  • Active Members
  • ***
  • Posts: 14
    • View Profile
Re: Half the Mounting Holes Drilled Out to 3/8"
« Reply #6 on: September 24, 2021, 04:24:27 pm »
I would just press bushings in or drill and tap for bushings before I welded on Aluminum.

You would have to TIG it and remachine. The work likely exceeds the cost of the part.