Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - askimball (Doc)

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 »
271
Star Reloaders / Re: Case kicker problem
« on: April 01, 2011, 07:53:49 pm »
I noticed on a Post, either here or on another forum that some\one adapted a Dillon Primer Warning Device......To you professional parts-adapers and part makers that should be "No hill for you stepper/s"
Regards

272
Star Reloaders / Re: Case kicker problem
« on: April 01, 2011, 01:57:30 pm »
I tried that also, so far the kicker seems to work........
Thanks guys for the helpful information........

273
Star Reloaders / Re: MOON OPERATION
« on: March 31, 2011, 02:21:43 pm »
I took a L shaped piece of aluminum and machined it to
fit at the edge of the Aluminum Base..Permentally
This should keep Fumbling around with shell casings....
Hope this works........

274
Star Reloaders / Re: HULME TEMPLATE
« on: March 29, 2011, 03:58:50 pm »
Maybe not for you, BUT, still would like a TEMPLATE to be sure it's
in the Correct Spot.....

275
Star Reloaders / HULME TEMPLATE/JIG TO DRILL FOR A CASE FEEDER
« on: March 29, 2011, 02:25:10 pm »
Last step to finish the Phelps loader project ;D
  I need the following

Hulme offered a kit to locate, drill and tap the hole for the case feeder on older models.


JUST NEED A TEMPLATE (LOCATE) :)

276
Star Reloaders / Re: #11 ALUMINUM BASE
« on: March 29, 2011, 01:49:52 pm »
Thank you....
Didn't think it did.......

277
Star Reloaders / #11 ALUMINUM BASE
« on: March 28, 2011, 07:17:40 pm »
Does a Phelps Aluminum Base have the same foot-print as
a Star Aluminum Base (Mounting Holes) ??? ??? ???

278
Star Reloaders / ADAPTER <>GOT 3 OFF eBAY<>
« on: March 28, 2011, 12:17:14 pm »
Gentlemen
I saw a Post that showed a Tool Head that had been Drilled & Tapped for
7/8" Dies ??? ??? with a Adapter.....

It showed a 11/16" Seating Die(?) in that Adapter......

So the Adapter was 7/8" OD x 11/16" ID

Anyone know who made this Adapter & where to get one ??? ???

279
Star Reloaders / Re: SCREWS
« on: March 28, 2011, 11:56:23 am »
LOCK & LOAD 'Lindy'

280
Star Reloaders / Re: SCREWS
« on: March 27, 2011, 01:27:35 am »
Looked all through my bolt box, had 3/8", but not that thread pitch...
8 x 32 ???
Did you have any 8x32's
Thanks Lindy

281
Star Reloaders / SCREWS > Thanks Everybody - Got Screws
« on: March 26, 2011, 09:48:28 pm »
I just finished putting the Phelps together, But I'm missing
2 - Screws:
#1 - Screw that holds the Crank Shaft Handle in.....???
#2 - The headless set screw in #79U-Shell Base Locating Strap...???

Would any of you guys happen to know the Thread Sizes for those 2 Screws..????

282
Star Reloaders / #50 Angle Lever Screw
« on: March 24, 2011, 11:56:01 pm »
Need the size data on this Screw:  #50 Angle Lever Screw
Anybody help ???

or should I ask for a McMaster-Carr part number.. :D ;D

283
Star Reloaders / Re: #82 SCREW
« on: March 24, 2011, 02:17:42 am »
Thank you Lindy

284
Star Reloaders / #82 SCREW
« on: March 22, 2011, 10:46:05 pm »
Anybody know the Thread Size of the #82 Primer Magazine Socket Screw ??? ???

285
Star Reloaders / Re: Shell Plate Thrust Nut
« on: March 22, 2011, 12:40:47 am »
Some of the 10mm cases seem tight in the shellplate??? ???

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 »