Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - askimball (Doc)

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 »
181
Star Reloaders / PART IDENTIFICATION
« on: August 17, 2011, 02:54:35 pm »
Has anybody come up with the part ID, Thread size, etc., on the Screw & Washer under the #12U Base, it restricts the
#24-Primer Punch from dropping down below the #12U-Steel Floor Base... ??? ???

I removed it and checked it out.... ::) :o :D

 Specs:
SCREW:
Slotted Fillister = 6-32 x 6/32"
WASHER:
Diameter = .375 OD
Screw Hole = 3/8"
Thickness = .038 varies

182
Star Reloaders / Re: Paint Match for Stars
« on: August 17, 2011, 03:02:30 am »
That's great :o
Thanks Lindy :D

There's a Auto Paint store down the street from my machinist............. 8)

183
Star Reloaders / THREADS
« on: August 15, 2011, 08:21:33 pm »
Dimensions & thread information........ ??? ::)  Please.. :)

#42 - Safety Cam Screw

184
Star Reloaders / Re: BLUE or BLACK
« on: August 14, 2011, 03:42:37 pm »
I comprehend that Bruce, that's why I brought it up, I'd never try that.............Would doing that oxide finish mess up the column &
the Bronze primer slide housing..?????   or doing the Brownell OXPHO finish........I believe I have a bottle of that......... ::)

185
Star Reloaders / Re: BLUE or BLACK
« on: August 13, 2011, 09:45:28 pm »
I got 2 Star steel bases that need to be done....If I take it to someone that does that, will I/should I take the Column out
of the base... ???

186
Star Reloaders / BLUE or BLACK
« on: August 13, 2011, 04:55:39 pm »
Anybody have a Fast / Easy method of Bluing or Blacking the Loader Parts.. ??? :-[ ???

i.e. The Steel Base........

187
Star Reloaders / Re: Die Question
« on: August 13, 2011, 04:48:12 pm »
Several of my Phelps dies have a Carbide ring inside, no marking on the Die ???

188
Star Reloaders / Re: Paint Match for Stars
« on: August 12, 2011, 09:16:56 pm »
Looking forward to that.............. 8)

189
Star Reloaders / STAR TAPER CRIMP DIE
« on: August 11, 2011, 07:03:16 pm »
This is a .45ACP die I acquired from a person I met who lives in San Diego.............
He purchased a Loader, before Star closed set up for .45ACP, BUT, it didn't come with a Taper Crimper, which was EXTRA.. :(

Should have done this on white paper.......... ::)

190
Star Reloaders / Re: Paint Match for Stars
« on: August 11, 2011, 06:49:24 pm »
WELL.. :(  :o
What is the Colour............. ??? ???

191
Star Reloaders / THREAD SIZE
« on: August 11, 2011, 01:54:11 am »
Need thread
for
#42 Safety Cam Screw... ???

192
Star Reloaders / Re: TAP & DRILL SIZE
« on: August 10, 2011, 06:18:09 pm »
Thanks Guys for all the 'Heads Up'

I have a Friend that has a HUGE Bridgeport Mill.. His vise is large enough to set the head down flat... He first lined up the hole with
a 3/8 drill bit, then drilled it, not sure what size drill he used...Measeured it with a inside type mike thing, checked it and took a
reamer & took off a little more, tapped it.....Perfect fit.....Charged me $10.00.

193
Star Reloaders / Re: TAP & DRILL SIZE
« on: August 10, 2011, 01:54:41 pm »
Thanks to rbwillnj  &  fc60   :)

194
Star Reloaders / Re: TAP & DRILL SIZE
« on: August 10, 2011, 01:13:08 pm »
Bruce
The Chart I have Shows 75% Thread  :-\

http://www.shender4.com/thread_chart.htm

195
Star Reloaders / Re: TAP & DRILL SIZE
« on: August 10, 2011, 01:46:04 am »
10-4 ;D

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 »