Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - askimball (Doc)

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 »
166
Star Reloaders / POTTER DIE COMPARISON
« on: September 09, 2011, 09:29:30 pm »
I received a email from a Jon Kay, couldn't find him in the name register...... ???

I'm going to Post a picture he emailed me.. :D

His email address is:  fishcop021(at)yahoo(dot)com

Here is a comparison picture of Dave's custom Potter sizing die in .41 Magnum (left), and an original Potter .38 Special sizing die (right).

167
Star Reloaders / Re: primer punch rocker arm guide screw?
« on: September 08, 2011, 01:58:11 pm »
It restricts the Primer Punch Rocker Arm from Falling below the bottom of the base..... ::)

I'm going to update what I stated about that Screw & Washer,,,After deep thought I concluded that it keeps the
PRIMER PUNCH from dropping down below the bottom of the Steel Floor Base..???
:o :-[

If Interested, the Data on the 2 parts.. :o

Specs:
SCREW:
Slotted Fillister = 6-32 x 6/32"
WASHER:
Diameter = .375 OD
Screw Hole = .136"
Thickness = .038 varies

168
Star Reloaders / PREVIOUS POST 'BLUE or BLACK'
« on: September 07, 2011, 10:01:19 pm »
On a Previous Post I inquired about Re-bluing the parts... A suggestion was offered, Brownells,   OXPHO_BLUE_reg__CREME
This very slow and does poorly, I've been using Brownells Creme Forula, DICROPAN, T-4 Touch-Up..... ;D

This does much better, faster and covers better than OXPHO.......... :o

Just a Helpful Hand.. :D ;D                                                              

169
Star Reloaders / Re: #45 Primer Punch Rocker Arm
« on: September 06, 2011, 03:24:48 pm »
Hey guys, thanks for all the help..............
If the wrong end like 'rbwillnj' eluded to, the primer punch protrudes above the Primer Slide locking up the machine ;D

There is 2 ends, the Fat ball (round end) end goes under the Tappet ;)
The smaller, not so round end, slightly pointed end works the Primer Punch... ;D

I'm doing a Drawing with Proper ID, which I'll Post later 8)

Also, I took out the little screw under the base that restricts the Primer Punch from Falling Below the #12U* Steel Floor Base,
Description is as Follows:

Specs:
SCREW:
Slotted Fillister = 6-32 x 6/32"
WASHER:
Diameter = .375 OD        
Screw Hole = .136"
Thickness = .038 varies
 

170
Star Reloaders / Up-Date On Part ID
« on: September 05, 2011, 06:31:17 pm »
The Little Screw & Washer under the Base that stops the Primer Punch from dropping down to far below the
#12U* Steel Floor Base,
Description is as follows:: :D ;D

SCREW
Slotted Fillister = 6-32 x 6/32"

WASHER
Diameter = .375 OD
Hole = 3/8"
Thickness = .038 varies

"Now You Know Said GI Joe"

171
Star Reloaders / Re: #45 Primer Punch Rocker Arm
« on: September 05, 2011, 06:15:35 pm »
fc60
Tried installing Rocker Arm (STAR) per your Drawing, It's Backwards, the end you show for Primer Punch
is the end for the Rocker Arm Tappet.............Wouldn't work that way..........PLEASE re-evaluate.......... ??? :D

172
Star Reloaders / Re: Hard down stroke?
« on: August 30, 2011, 03:38:17 pm »
He is 'fc60' on this Forum (David Wilson)

He DOES FANTASTIC PROFESSIONAL WORK  :D

I'm Attaching a Picture of his Dies compared to Star Dies....... :o

Bottom row are his dies, last die on the right is a Taper Crimp Die..... :D

He also at one time made a stemmed Taper Crimp Die (3/8" Shaft).. :o

173
Star Reloaders / Re: #45 Primer Punch Rocker Arm
« on: August 30, 2011, 03:26:12 pm »
Thank you very much.. :D ;D

174
Star Reloaders / #45 Primer Punch Rocker Arm
« on: August 29, 2011, 06:49:21 pm »
HELP !!

Need a exact copy of the Primer Punch Rocker Arm   >   NOT THE PICTURE SHOWN in the STAR MACHINE WORKS
site........ :o
DOESN'T HELP... :o

I need to know which end is the #46 Rocker Arm Tappet end.....

175
Star Reloaders / Re: Cleaning the seating die
« on: August 25, 2011, 06:37:55 pm »
Cut down on the size lube...See process of blocking the upper & bottom holes on the sizing die.
OR change lube...........

176
Star Reloaders / Re: Custom Potter Engineering Die
« on: August 25, 2011, 06:33:10 pm »
eMAIL THEM TO ME...............

askimball (at) comcast (dot) net

177
Star Reloaders / Re: Custom Potter Engineering Die
« on: August 24, 2011, 06:35:18 pm »
Any chance of a picture of the Shell-plate.............. ::)

178
Stars Want to Sell/Want to Buy / Re: Hulme top plate
« on: August 20, 2011, 05:47:35 pm »
10-4.. :D

179
Stars Want to Sell/Want to Buy / Re: Hulme top plate
« on: August 20, 2011, 01:49:21 pm »
Mr Bruce
Can you have / show us a picture of a Dillon top plate for the Hulme.. ??? ::)

180
Star Reloaders / Re: manual
« on: August 17, 2011, 05:42:33 pm »
Bob
Where did you Download them from.. ??? ???
Phelps Setup Instructions... :)

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 »