Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - askimball (Doc)

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 »

166

Star Reloaders / POTTER DIE COMPARISON

« on: September 09, 2011, 09:29:30 pm »

I received a email from a Jon Kay, couldn't find him in the name register......

I'm going to Post a picture he emailed me..

His email address is: fishcop021(at)yahoo(dot)com

Here is a comparison picture of Dave's custom Potter sizing die in .41 Magnum (left), and an original Potter .38 Special sizing die (right).

167

Star Reloaders / Re: primer punch rocker arm guide screw?

« on: September 08, 2011, 01:58:11 pm »

It restricts the Primer Punch Rocker Arm from Falling below the bottom of the base.....

I'm going to update what I stated about that Screw & Washer,,,After deep thought I concluded that it keeps the
PRIMER PUNCH from dropping down below the bottom of the Steel Floor Base..

If Interested, the Data on the 2 parts..

Specs:
SCREW:
Slotted Fillister = 6-32 x 6/32"
WASHER:
Diameter = .375 OD
Screw Hole = .136"
Thickness = .038 varies

168

Star Reloaders / PREVIOUS POST 'BLUE or BLACK'

« on: September 07, 2011, 10:01:19 pm »

On a Previous Post I inquired about Re-bluing the parts... A suggestion was offered, Brownells, OXPHO_BLUE_reg__CREME
This very slow and does poorly, I've been using Brownells Creme Forula, DICROPAN, T-4 Touch-Up.....

This does much better, faster and covers better than OXPHO..........

Just a Helpful Hand..

169

Star Reloaders / Re: #45 Primer Punch Rocker Arm

« on: September 06, 2011, 03:24:48 pm »

Hey guys, thanks for all the help..............
If the wrong end like 'rbwillnj' eluded to, the primer punch protrudes above the Primer Slide locking up the machine

There is 2 ends, the Fat ball (round end) end goes under the Tappet

The smaller, not so round end, slightly pointed end works the Primer Punch...

I'm doing a Drawing with Proper ID, which I'll Post later

Also, I took out the little screw under the base that restricts the Primer Punch from Falling Below the #12U* Steel Floor Base,
Description is as Follows:

Specs:
SCREW:
Slotted Fillister = 6-32 x 6/32"
WASHER:
Diameter = .375 OD
Screw Hole = .136"
Thickness = .038 varies

170

Star Reloaders / Up-Date On Part ID

« on: September 05, 2011, 06:31:17 pm »

The Little Screw & Washer under the Base that stops the Primer Punch from dropping down to far below the
#12U* Steel Floor Base,
Description is as follows::

SCREW
Slotted Fillister = 6-32 x 6/32"

WASHER
Diameter = .375 OD
Hole = 3/8"
Thickness = .038 varies

"Now You Know Said GI Joe"

171

Star Reloaders / Re: #45 Primer Punch Rocker Arm

« on: September 05, 2011, 06:15:35 pm »

fc60
Tried installing Rocker Arm (STAR) per your Drawing, It's Backwards, the end you show for Primer Punch
is the end for the Rocker Arm Tappet.............Wouldn't work that way..........PLEASE re-evaluate..........

172