Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - starman

Pages: 1 2 3 4 »
1
Stars Want to Sell/Want to Buy / Re: WTS - New Primer Magazines
« on: October 18, 2010, 10:06:24 pm »
I must say that looks like good work and they are hard to find keep it up

2
Star Reloaders / Re: new owner ... lots to learn
« on: September 24, 2010, 04:32:09 pm »
with the powder brum you just drill a hole threw it then turn the brum to the off position which is the holes are at off position where the powder can not go threw the drum put in a set sew to hold the brum off or on then cut a 9/16x27 thread for the powder slide housing cover, rcbs little dandy or  the old pacific  take a look at it you can do it. Now some people do not like the power shut off but that is up to them I have beem using mine for a long time with no problem I do not leave powder in my machine. good luck and have fun

3
Star Reloaders / Re: new owner ... lots to learn
« on: September 22, 2010, 05:12:29 pm »
I have 3 powder shut off made two of them so easy to make just get the right powder housing old paciffic or  the little rcbs with powder dums

4
Star Reloaders / Re: 45 ACP Post TC Die
« on: August 27, 2010, 04:45:12 pm »
YES

5
Star Reloaders / Re: 45 ACP taper crimp die Question
« on: May 07, 2010, 03:19:31 pm »
there is two types of taper crimp die, screw in and post type they just taper crimp only in the last station

6
Star Reloaders / Re: Any interest in new star type reloader?
« on: March 16, 2010, 11:34:17 pm »
I thought the one built in Australia was a Willis mybe im wrong boy that would be a first in a long time

7
In my last 33 years of the star I have never had that problem but I must say I do keep it clean

8
.472 at case mouth with win brass 3.5 Bull 185 SWC H&G and that is with range lead it is a Clark 45 long slide my biggest problem is with the target they all go into the same hole at 25 yards that is why I always take my Clark 38 long slide but most of the time I end up with the same problem

9
Star History / Re: taper crimp die
« on: November 27, 2009, 03:08:08 pm »
I think that is nice

10
all you do is OD grind the dies to size then cut the thread or thread grind the thread come on what is the big deal here about rethreading a die

11
Star Reloaders / Re: manual
« on: September 24, 2009, 06:27:03 pm »
I can send you a copy I will have to have one made

12
Star History / Re: Star Price History
« on: September 18, 2009, 05:09:55 pm »
it look like it was repainted  too and the star decal was upside down I think I will come out of the closet oh I mean one of my stars

13
Star Reloaders / Re: Looking for Paul Jones, Star Loading enthusiast
« on: September 15, 2009, 10:59:33 pm »
You have to give him some slack he is here in Kalifornia as I keep saying a lot of HOT air here, hesa kickinnnnnnn

14
Star Reloaders / Re: Cover for the Star Reloader?
« on: September 15, 2009, 03:01:15 pm »
it sounds like you have a good idea for a cover it would be nice to have a nice cover that would really do the right job for protection rust and all. Do let me tell you work always gets in the way DONT do it

15
Star Reloaders / Re: Looking for Paul Jones, Star Loading enthusiast
« on: September 13, 2009, 11:41:13 pm »
He is still alive and somtimes kicking

Pages: 1 2 3 4 »