Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - maurilew

Pages: 1 2 »
Star Reloaders / Re: Powder Drain
« on: April 30, 2015, 10:44:05 pm »
Thanks to Joe pics are present
For sake of time and space(plus my hazzardous computor ability) will refer you to WTB/WTS section page one bottom of page is a muddled notice giving answers to you ?,s
Regards  Maurilew(aka "Ma")

Star Reloaders / Re: Powder Drain
« on: April 10, 2015, 06:45:41 pm »
Sent a pm hope u got it  Maurilew  (aka "Ma")

Star Reloaders / Re: Powder Drain
« on: April 10, 2015, 06:41:33 pm »
Sent a pm hope u got it     Maurlew(aka "Ma"

Stars Want to Sell/Want to Buy / Powder Drain/Shutoff
« on: March 07, 2015, 08:55:52 pm »
Reloader Forum;
Time to update previuos ad. Due to space usage,will be brief.

It replaces top half powder housing. Once in place there no further modification to loader.
, there is a cross slide.when in place to load it sits directly on brass powder slide.
When extended outward it move powder to drain position directly over down tube.Tube at this time is blocked by expandable plug. At this time there is no powder other than charge in bar ready to drop into last case to be loaded.
$55.00 +$3.25 s/h     Additional info will be available upon request at mlewis at sti dot net 559-683-5354

Regards to all     maurilew   aka "Ma"

Star Reloaders / Re: Brass "Y" powder dump
« on: October 15, 2014, 07:20:42 pm »
Very nice unit.
However, there appears to be an area mentioned in ad,on ebay, about left over powder having to be taken care of after reloading stops. A total seperate function in its self,using another case,and another pull on handle
Is there any estimate of how much powder is left in the brass tube. Will one case hold it all?

Maurilew  aka  "Ma"

Stars Want to Sell/Want to Buy / Re: Powder Cutoff WTB
« on: June 05, 2014, 01:24:19 pm »
Thanks again Bruce     Ma

Loading Data & Reloading Procedures / Harvey Protex Bullets ???????
« on: January 17, 2013, 06:56:51 pm »
Has anyone out there experimented with this bullet ?
Found a box of washers, mould with handles in a pile of gift material l got the other day. Don,t they go way back in reloading history?

Gratfull for any info   Maurilew "Ma"

Stars Want to Sell/Want to Buy / Re: WTB - Powder Drains
« on: October 01, 2012, 11:12:42 am »
Thanks Bruce.....I will contact Maurilew..... :)
Thanks Bruce (maurilew  "Ma")

Star Reloaders / Re: STAR vs PHELPS
« on: November 18, 2011, 10:07:16 am »
My nickles worth,,,,
When a person buys a unit for a set price on the forum then later sells same on ebay for an 86% markup,there is a question about charactor trait.

Either one heck of a salesman, or one who would take any opportunity to shaft the unsusspecting. The decision is up to the individuals involved.

A part should be clearly and accurately listed.

I have made my decision

I,ve made mine

« on: September 15, 2011, 12:35:09 am »
Certainly have been numerous comlpaints about Bill Cunningham on the forum.Someday l would like to meet a person who by making any attempt, however so slight,raises so much ire. Guess some just sit back and rest on their laurels of their past,bad mouth someone who steps up and attempts to do what he has called for years.

All you fellas who are trying to keep the Stars from becoming extinct, no matter how small,KEEP IT UP !!!!!!!!

Star Reloaders / Re: TAP & DRILL SIZE
« on: August 10, 2011, 12:59:27 am »
my book says 41/64 alum    21/32 steel

Star Reloaders / Re: rare
« on: July 15, 2011, 04:23:25 am »
Google has a very complete article about the 475 Wildey Pistol.


Star Reloaders / Re: HOW TO POST PICTURES
« on: February 01, 2011, 11:45:59 pm »
Doc; wishing you luck on a response.  asked same question  , got one response, and it stopped short of complete info , so still waiting. have patience.

Loading Data & Reloading Procedures / 38 Sp. Peters Cases
« on: December 09, 2010, 11:30:38 pm »
Have quite abunch of Peters cases with large primer holes. these are loaded rnd nose 38,s. and seem to be moderate in power. shot a few extras but hanging on to full boxes
 any one have some info on them?

Loading Data & Reloading Procedures / Re: Static charge?
« on: December 09, 2010, 03:19:54 pm »
not too sharp on elecricity. but electricity has to hve a path to follow, a conductor. if there is no continuity to grd the current has no place to go. so it would not spark/arc at point of contact with press. however assuming press is mounted on a non-conductive suface. oh hell,, just shot down my first academic oratory for today.


Pages: 1 2 »