Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - rbwillnj

631
Star History / Re: Star Price History
« on: May 31, 2011, 09:41:47 pm »
The price list for 1993 would be interesting.   That was getting pretty close to the end of production.

632
Star Reloaders / Re: CPM Machine ?
« on: May 30, 2011, 05:11:09 pm »
Take a look at these threads on the forum, it will answer many of your questions.

http://www.starreloaders.com/forum/index.php?topic=664.0

http://www.starreloaders.com/forum/index.php?topic=192.0


I am surprised that it has a Hulme case feeder as CPM made their own case feeder

Bruce

633
Star Reloaders / Re: Star Lifetyme Dies
« on: May 27, 2011, 10:11:00 pm »
I have Lifetyme two stage dies for both 45 ACP and 38 Special.  Both sizing rings are carbide.

I have never been clear about the purpose of two stage sizing dies.  One member suggested they were for sizing Remington brass which he suggested was thinner.

Bruce

634
Star Reloaders / Re: Mystery Press
« on: May 24, 2011, 04:46:20 pm »
Star did make an in-line press, but that doesn't look anything like it.

635
Star Reloaders / Re: Star Lifetyme Dies
« on: May 23, 2011, 11:50:03 pm »
I have seen some adapters for 11/16-24 to 7/8-14 adapters on eBay from time to time, but they are not common.

If you really need 7/8-14 dies, you would be better off to sell the Star dies and buy a set of 7/8-14 dies.  There are plenty of good ones to choose from.   I might be interested in the 30 Carbine dies that you have, as well as the 38 Special 2S dies.

Bruce

636
Star Reloaders / Re: Safety Cam Modification For Taper Crimp Die
« on: May 20, 2011, 11:54:16 am »
There are two problem with this design.  One is that it is caliber specific.  The size/length  of the "hook" is different for each caliber.   The other problem is that there had to be clearance under the taper crimp die to be able to use this safety cam.    By the way, it is an autoeject safety cam.  The extra spring works in conjunction with the case feeder to eject the loaded round with the tool head is raised.

This is the only one I have ever seen.

637
Star Reloaders / Re: Safety Cam Modification For Taper Crimp Die
« on: May 20, 2011, 12:57:53 am »
Dave,

I think this might be what your looking for.   I posted pictures of this a while back.   This is original Star.


Bruce

638
I wouldn't use heat.  You can bend it.  Leave it on the tool head.   To bend it in, I give it a couple light taps with a dead blow hammer.  To move it out, I generally find some way to get a wrench on it and bend it out.  You don't have to bend it very much to change the adjustment quite a bit.

639
Star did a pretty good job of making it so that you can swap different tool heads on different Universal machines.  However, you cannot put a Progressive tool head on a Universal machine and vice verse without also changing the angle lever cam.

So did the tool head you are using come from a Progressive?  If so, you will not be able to bend the angle lever cam enough to compensate.

What I asked was if the number on the angle lever cam is that same number that is stamped in the tool head in the round cut out next to where the angle lever cam mounts.   If the numbers don't match (number and font), it is not the cam that was fitted to that tool head at the factory.

Bruce

640
You can adjust alignment of the primer punch with the primer slide by bending the Angle Lever Cam #49U inwards or outwards.  To make the primer slide go in further, bend the angle lever cam outwards....just a little bit.

Does the number on the Angle Lever Cam match the number on the tool head?

Bruce

641
Star Lubricator & Resizers / Re: STAR LUB/SIZ ACCESSORY
« on: May 05, 2011, 08:49:51 pm »
You guys are giving this a whole lot of thought...........to save $3.49

642
Star Reloaders / Re: Modifications to powder charge bars
« on: May 04, 2011, 11:33:53 am »
The Hornady bushings are 1/2" high while the 00 charge bars are 5/16" thick.  So no, you can't use the Hornady bushings in a drilled out 00 charge bar.

Berdon, and I think another company offered 00 charge bars with bushing sets, but no one offers bushings for 00 charge bars at this time.

I sell a 1/2" charge bar that accepts Hornady bushings.  I also include a set of spacers to convert a 00 powder slide housing to a 1/2" housing.  I am currently out of stock, but I plan to make a run of them in the near future.

Bruce

643
Star Reloaders / Re: PICTURES OF PHELPS INDEXERS
« on: May 01, 2011, 07:01:29 am »
I see that you have a Phelps Progressive (not Universal).   I knew Phelps offered a Progressive machine, but this is the first one I have ever seen.

644
Star Reloaders / Re: .45 Auto Rim vs .45 ACP Adjustments
« on: April 30, 2011, 11:52:08 am »
Assuming you are shooting the same bullet and load (which you can), you shouldn't have to change anything except the shell plate.

645
Star Reloaders / Re: Loading .223 on Star
« on: April 28, 2011, 10:51:45 pm »
From the reading that I've been doing on the forum it's been suggested that an expander above the prime station helps hold the casing for priming as well.


It's certianly true with every other caliber so I don't know why it wouldn't hold true for .223,.... but that doesn't mean it's necessary.   Other members might be able to offer more insight.

Bruce