Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - SWANEE

Pages: 1
1
Stars Want to Sell/Want to Buy / WTB-38spl semi-rimmed brass
« on: December 07, 2013, 03:04:56 pm »
Some time ago a member had some of this brass listed, don't remember who tho, Hope fully someone will get back to me on this brass, this brass was made for the (AMU) Army marksmanship Unit of Ft Benning, Ga. Was used in a 1911 colt. Thanks for any help.SWANEE

2
Stars Want to Sell/Want to Buy / WTB-Star luber fixer upper
« on: July 20, 2013, 08:56:59 pm »
Looking for a Star lube sizer that could use some fixing up, no broken parts tho. A PM would be the best way to get hold of me.

3
Stars Want to Sell/Want to Buy / WTS-Star Universal reloader '38'
« on: May 01, 2013, 07:04:06 pm »
After much mind searching I have decided to part with my Star, seems like I just do not have the time to put it to use so do not want it to be wasted when there are folks who can get use out of it. Just a little bit of history on this machine, was bought in the '68's and was used for about 2 years and then covered up until about 3 years ago a friend bought it but had never been a reloader and decided was not what he was going do so he sold it to me with the understanding he gets first chance at buying it back, talked to him and does not want it back. I was going to set it up for 45 also, comes with an extra tool head set up in 38, some of the 45 parts I got from Bruce (RBWILLNJ), Just a lot of extra parts that I have gotten over the years, hope I can get the pic's listed with this Star and all the extras but am not to sharp with this computer so will see what happens, a PM is the best way to get answers to your ?'s. I'm asking a $1000. shipped, the only trading I might be interested in would be a Star luber with dies. This listing will not be for a long time, maybe a week or two.
1st pic, 3 45 s-plates & 1 9mm, all were made by Berdon, i'm including them at no cost, should work, maybe not.
4th pic, L primer slide & punch (never used)
5th pic, powder magazine w/alarm, that was my proto-type that Mr Dillon took and ran off with.
6th pic, primer tubes, 1968 book & reloader cover.
7th pic, 2 pcs are 45 carbide sizers by Phelps, the rest are all 'I believe' Star.
8th pic, 10 various powder slides, one is one that I made to use powder bushings, the bushings are all pilot bushings, all are '00'
9th pic, complete tool head in 38 spl and is a real nice piece.

SOLD PENDING FUNDS

4
Stars Want to Sell/Want to Buy / 3/4in powder set up
« on: October 30, 2011, 11:20:57 am »
I'll try and post pic's, i'st in line is Leopoldmrk4, 2'nd is cc656d, we'll see what happens after that. Powder set-up is a star clone made from cast iron, 1/2in housing w/1/4in spacer, 3 of the bushings are pilot hole drilled to be reamed for your desired drop, $100. will get it shipped.

5
Star Reloaders / Case feeder I D ?
« on: September 04, 2009, 06:22:27 pm »
OK, I know someone will tell me a little about this case feeder, first one I've seen like this. Thanks

6
Star Reloaders / J hoag adj powder chg bars
« on: May 06, 2009, 11:08:14 pm »
Can anyone put a date of mfg on these adjustable chg bars, also was this HOAG gent a California gun smith? ??? Any help would be appreaciated. I also have a tool head drilled out for 7/8-14 dies, it only has a number marked where star would have their name and pat #.  I know it is not a berdon cause I have several of them, did phelps have a tool head for standard dies :-\?

Pages: 1