Author Topic: Phelps die head in 7/8x 14  (Read 12326 times)

0 Members and 1 Guest are viewing this topic.

wayne

  • Guest
Phelps die head in 7/8x 14
« on: September 06, 2010, 11:38:36 pm »
I recently bought a phelps die head which is drilled and tapped for 7/8x14 dies but only the sizing and seating/crimping positions are 7/8.What is conventional wisdom for the mouth expanding position.I wrongly assumed I could use a normal die set with this head.Thoughts solutions?
Wayne

bummer7

  • Active Members
  • ***
  • Posts: 81
    • View Profile
Re: Phelps die head in 7/8x 14
« Reply #1 on: September 07, 2010, 10:12:03 am »
I recently bought a phelps die head which is drilled and tapped for 7/8x14 dies but only the sizing and seating/crimping positions are 7/8.What is conventional wisdom for the mouth expanding position.I wrongly assumed I could use a normal die set with this head.Thoughts solutions?
Wayne


Wayne,

Perhaps I don't understand your question.  But why can't you decap the primer and size the case at the first station without belling the case mouth? 

-s

tony barone

  • Active Members
  • ***
  • Posts: 148
    • View Profile
Re: Phelps die head in 7/8x 14
« Reply #2 on: September 07, 2010, 11:05:51 am »
The belling station for the Star has a shell expander that was designed to hold the shell
 down, bell it and seat the primer without stressing the shell plate. Another manufacturer's die won't do that.

fc60

  • Active Members
  • ***
  • Posts: 480
    • View Profile
Re: Phelps die head in 7/8x 14
« Reply #3 on: September 07, 2010, 11:18:17 am »
Greetings,

I would suggest using the Star 1/2-27 threaded expander.

Cheers,

Dave Wilson

wayne

  • Guest
Re: Phelps die head in 7/8x 14
« Reply #4 on: September 07, 2010, 06:01:28 pm »
The dies I have are  3 and 4 die sets,belling the case mouth is my quandary along with typing. Dave where can these belling dies you suggest be obtained?

fc60

  • Active Members
  • ***
  • Posts: 480
    • View Profile
Re: Phelps die head in 7/8x 14
« Reply #5 on: September 07, 2010, 08:09:15 pm »
Greetings Wayne,

On the Star Parts List, the item you seek is #16, Shell Expander Plug. If you need one for 45 ACP or 38 Special, I am sure someone on the list has a spare. Should you need one for a different caliber, I can machine one for you. I need to know the bullet length and diameter.

Cheers,

Dave Wilson

tony barone

  • Active Members
  • ***
  • Posts: 148
    • View Profile
Re: Phelps die head in 7/8x 14
« Reply #6 on: September 08, 2010, 01:45:23 pm »
Why not give Bill Cunningham from Star Machine Works at 209-295-5000 he might be able to fill your needs.

rbwillnj

  • Global Moderator
  • ****
  • Posts: 1216
    • View Profile
    • Star Machine Works
Re: Phelps die head in 7/8x 14
« Reply #7 on: September 08, 2010, 02:26:01 pm »
Although it's best to use a Star expander to counteract the force of the priming operation, you should be able to use a three die set by expanding in what is normally the seating station, and seating/roll crimping in the taper crimp station.   If you need to do a separate taper crimp in the last station, the easiest way is to use the Star expander.
Star Machine Works
Star, the original blue Press.  Made by machinist, not machines.
www.StarMachineWorks.com