Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - varmintpopper

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 »
61
Loading Data & Reloading Procedures / Re: Taper Crimp Dies
« on: October 07, 2019, 01:11:00 am »
Sweet Success.

Good Shooting

Lindy

62
Loading Data & Reloading Procedures / Re: Taper Crimp Dies
« on: October 03, 2019, 12:09:19 am »
wv109323

Greetings
Taper crimp dies should adjust up or down to obtain the crimp You desire. I would Screw the die an eighth of an inch or so counter clockwise,  then try crimping again, keep doing this until You get the crimp You want. Good luck

Good shooting

Lindy

63
Star Lubricator & Resizers / Re: Cannot get properly lubed bullets
« on: July 30, 2019, 12:23:13 am »
megasupermagnum

You Prob. know this but the "high pressure" to the sizing die is supplied by Pump plunger piston (S124)  and not the reservoir spring (S129), the res. spring only supplies lube to the
piston and cylinder located in the base of the unit. The piston must make a full stroke to supply lube to the Die. The only adjustments for this is the bolt (S114).
Take a look in this area and make sure that the piston (S124) is being pushed all the way out by spring (S125) with the operating  handle all the way up. if not, the piston could be binding
in the cylinder.
Hoping You find the prob. soon, These really are great little machines.


Good Shooting

Lindy

64
Star Reloaders / Re: Convert STAR Progressive to load 9mm ?
« on: January 02, 2019, 07:56:07 pm »
With different dimensions on some of the shell plates, Has anyone had a problem with the primers lining up properly with the case head primer hole ?

Good Shooting

Lindy

65
Star Reloaders / Re: Helpfull Modification
« on: October 12, 2018, 02:16:56 am »
I did not fab the part in the picture but home made something very similar.  It allows removing a case for reasons such as dents, splits or for other things that require their removal and allows for replacing the removed case if needed.

Good shooting

Lindy

66
Star Reloaders / Helpfull Modification
« on: October 10, 2018, 11:31:58 pm »
https://imgur.com/PzMt6se

Good Shooting

Lindy

67
Star Reloaders / Re: Automation of a Star
« on: August 31, 2018, 11:06:30 pm »
None of the above. Just for Me and for just the fun of it  !

Good Shooting

Lindy

68
Star Reloaders / Automation of a Star
« on: August 30, 2018, 04:53:38 pm »
Automation Of a Star reloader (mostly home made)

https://imgur.com/smuWazk

Good Shooting

Lindy

69
Stars Want to Sell/Want to Buy / Re: WTB: MA SYSTEMS ROTO-EZE
« on: July 11, 2018, 12:31:53 pm »
Moon unit Indexers:  http://www.ray-vin.com/star/indexerhome.htm


Good Shooting

Lindy

70
Stars Want to Sell/Want to Buy / Re: WTB: MA SYSTEMS ROTO-EZE
« on: July 01, 2018, 01:06:41 pm »
I have used the MA system roto ease but found that the "Moon Indexer" is a much better indexer by far.
May I suggest You take a look at it.
https://www.youtube.com/watch?v=v7EebVoej6w

Good Shooting

Lindy

71
Stars Want to Sell/Want to Buy / Re: WTB: MA SYSTEMS ROTO-EZE
« on: June 12, 2018, 12:44:58 am »
Bob
I no longer possess an "Eject Ease" or a "Roto Ease" but do have the manuals for both. Send me Your Home Address By Email and I'll mail You a copy.
Don't know if they will help much as there is not much info in them but a few drawings and pic's.

miltonetime (at sign)aol (dot) com

Good Shooting

Lindy

72
Star Reloaders / Re: Star Loader set up questions
« on: May 30, 2018, 08:18:04 pm »
https://youtu.be/bx7kDdReQ_E

This video may be of some help.

Good Shooting

Lindy

73
Star Reloaders / Re: Powder slide scored by debris
« on: May 02, 2018, 01:14:21 am »
I always try to wipe off the top of the powder container that I'll be using to fill the powder hopper with as dust, dirt and debris  tends to find its way there and can find its way into the hopper.

Speculation of course.

Good Shooting

Lindy

74
Star Reloaders / Re: Star loader with extras
« on: April 19, 2018, 10:58:52 pm »
Thing of beauty!  Would love to try out one of those bullet feeders.


https://imgur.com/a/6x6yQS0

This the cartridge ejection system that I use ,,, No moving parts.

75
Star Reloaders / Re: Star loader with extras
« on: April 17, 2018, 10:44:04 pm »
https://imgur.com/a/6x6yQS0

A Video Making Bullets

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 »